HDBOX 9105+ HD PVR

[milkasv]

Dobrý deň,

po roku som sa rozhodol skusiť stb HDBOX 9105+ no po zapnuti na mna vybehla hláška L7.26 tak som postupoval podľa návodu nahral tam cez CHUP .ird subor a potom som dal usb_kernel a usb_rootfs prebehlo to no teraz svieti na zeleno a blika červené a na displeji piše 7819 neviem ho rozchodiť pripojil som ho na RS232 a vypisuje to takýto log https://pastebin.com/XD1UVdgG. Akoby to očakávalo uboot ktorý keď tam dam tak sa dostanem naspäť na L7.26 neviete niekto poradiť ako by som ho rozchodil ? Satelit by sa mi zišiel na chatu. Niesom v tom nejaký expert ale ani úplny začiatočnik. Vďaka

[milkasv]

Skušal som ešte listovať fórum a niekto mal podobný problem a pomohla mu znema bootloadera, že ten čo mam je poškodený. Tak sa chcem spýtať, že ako by som to docielil

[vodka]

daj uboot a potom orginal http://www.ab-forum.info/viewtopic.php?f=189&t=46973
a tak nejaku enigmu aj tu
https://hdbox.sk/podpora/

[milkasv]

Tak teda som skusil podla tvojho návodu origo fw mi prebehol bez problemov restartoval som dal som ten upgrade_loader9105+.ird subor od enigmy kde mi na rs232 vypísalo takýto výstup a na displeji END
' ▒▒(Re)start USB...
Front USB: scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
.
system volume information/
.
131136 upgrade_loader_9105+.ird
==> find ird upgrade_loader_9105+.ird [131136 ] <==

1 file(s), 1 dir(s)

==> usb_loading start upgrade_loader_9105+.ird
reading upgrade_loader_9105+.ird
.
.
............
ret=> 131136
Loader_WriteFlashData[0] size=206836
Loader_WriteFlash size=0x327f4 offset=0x0
Erasing at 0x20000 -- 100% complete.

Writing data at 0x0 -- 0% complete. [0 0]


A potom som dal USB s usb_rootfs.img a usb_kernel.img aa vypisuje to toto dookola
U-Boot 1.3.1 (Nov 9 2013 - 23:21:23) - stm23_0046

DRAM: 256 MiB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
set ethaddr 00:1e:b8:12:f1:1e
done
Setup mac address.
usb upgrage
USB: scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
(Re)start USB...
USB: scanning bus for devices...

Board: STx7111-7819 [32-bit mode]


U-Boot 1.3.1 (Nov 9 2013 - 23:21:23) - stm23_0046

DRAM: 256 MiB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
set ethaddr 00:1e:b8:12:f1:1e
done
Setup mac address.
done
Hit any key to stop autoboot: 0
(Re)start USB...
USB: scanning bus for devices... 2 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
** Can't read from device 0 **

** Unable to use usb 0:1 for fatload **
## Booting image at 80000000 ...
Image Name: Linux-2.6.32.61_stm24_0217
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2556676 Bytes = 2.4 MiB
Load Address: 80801000
Entry Point: 80802000
Verifying Checksum ... Bad Data CRC

NAND read: device 0 offset 0x60000, size 0x300000

Reading data from 0x35f800 -- 100% complete.
3145728 bytes read: OK
## Booting image at 80000000 ...
Image Name: Linux-2.6.32.61_stm24_0217
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 2556676 Bytes = 2.4 MiB
Load Address: 80801000
Entry Point: 80802000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK

Starting kernel console=ttyAS0,115200 panic=1 ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs rw coprocessor_mem=4m@0x40000000,4m@0x40400000 - 0x00000000 - 0 ...



Board: STx7111-7819 [32-bit mode]


U-Boot 1.3.1 (Nov 9 2013 - 23:21:23) - stm23_0046

DRAM: 256 MiB
NAND: 256 MiB
In: serial
Out: serial
Err: serial
set ethaddr 00:1e:b8:12:f1:1e
done
Setup mac address.
done
Hit any key to stop autoboot: 0
(Re)start USB...
USB: scanning bus for devices...

[milkasv]

Tak asi som prišiel na chybu bolo mi povedané že mam skusiť nahrať default a potom vymazať všetko vo /var cez protect a erase no lenže ten mi nefunguje a skusil som fli a ten ma takýto vystup :

HDK7111> fli
Bank # 1: missing or unknown FLASH type

Je možne že odišla na ňom FLASH pamäť ?

[dlhe_pole]

tak tak .. flash-ku mas v čavese