Bulsatcom 39°E
Pravidla fóra
Nediskutovať - sekcia slúži výhradne pre download !
Nediskutovať - sekcia slúži výhradne pre download !
Re: Bulsatcom 39°E
Máš pravdu ten oscam ymod 18.53 samostatně nejede ani karta jak to mam zprovoznit jde mi jen cccam2.3.0
Re: Bulsatcom 39°E
cccam2.3.0 ti ide preto že tam netreba nič nastavovať,uprav si oscam server pre ice kartu
Re: Bulsatcom 39°E
Tak to teda nevím jak to upravit takový borec nejsem mam tento přijimač 14 dní.
Re: Bulsatcom 39°E
Musis citat vlakno o oscame, ked chces nieco vediet o nom. Tu na fore predsa je vsetko popisane.........narychlo ti dam toto
http://www.satnigmo.com/oscam-configs/s ... orks-card/
http://www.satnigmo.com/oscam-configs/s ... orks-card/
VU UNO openATV, plna skrina kramov
Tento cely prispevok bol napisany bez financnej pomoci EU a tapatalku!
Niektore mimovladky a OZ by mali byt zakazane zo zakona, lebo sluzia len na rozvracanie statov.
Tento cely prispevok bol napisany bez financnej pomoci EU a tapatalku!
Niektore mimovladky a OZ by mali byt zakazane zo zakona, lebo sluzia len na rozvracanie statov.
Re: Bulsatcom 39°E
Ale kde to najdu v menu oscam server tu je to popsané ale jak se k tomu dostat.
Re: Bulsatcom 39°E
Pri ATV je config v usr/keys dostanes sa tam clientom ftp. Neviem co pouzivas, tam si pozri ako mas defonovane rozhranie a potom mozes aj cez to. IP a prislusny port.
MAs vobec vyskusane nejake ftp? Alebo zatial si absolutne okrem menu v boxe nic nerobil, tazko radit takto......
MAs vobec vyskusane nejake ftp? Alebo zatial si absolutne okrem menu v boxe nic nerobil, tazko radit takto......
VU UNO openATV, plna skrina kramov
Tento cely prispevok bol napisany bez financnej pomoci EU a tapatalku!
Niektore mimovladky a OZ by mali byt zakazane zo zakona, lebo sluzia len na rozvracanie statov.
Tento cely prispevok bol napisany bez financnej pomoci EU a tapatalku!
Niektore mimovladky a OZ by mali byt zakazane zo zakona, lebo sluzia len na rozvracanie statov.
Re: Bulsatcom 39°E
Tak to je zlé do boxu umím přes totalcommander dat přes svou adresu přijimače kliče softcam key i picony ale adresy jsem neskošel.
Re: Bulsatcom 39°E
napiš mi do zprávy skype, pokud máš tedy....můžem to omrknoutvincek píše:Ale kde to najdu v menu oscam server tu je to popsané ale jak se k tomu dostat.
zgemma h7s, Vu+solo2, t-90 4°W-39°E
Re: Bulsatcom 39°E
No tak predsa totalol ked tam vlezes tam vidis aj konfig oscamu v tom /usr/keys tak to stiahni k sebe do pc, tam to uprav podla toho linku co som sem dal, nakopiruj naspat do boxu, restert a hotovo....
VU UNO openATV, plna skrina kramov
Tento cely prispevok bol napisany bez financnej pomoci EU a tapatalku!
Niektore mimovladky a OZ by mali byt zakazane zo zakona, lebo sluzia len na rozvracanie statov.
Tento cely prispevok bol napisany bez financnej pomoci EU a tapatalku!
Niektore mimovladky a OZ by mali byt zakazane zo zakona, lebo sluzia len na rozvracanie statov.
Re: Bulsatcom 39°E
Tak jsem to přepsal ten mg_cfg celý.Pošlu ti to a koukni jestli to mám dobře ale nejde mi to.
Nemáte oprávnění prohlížet přiložené soubory.
Re: Bulsatcom 39°E
Not to si poondil, ty si skrizil oscam a mgcamd, to je nejaky novotvar......
No pockaj skusim ti poslat nieco v ss na Mikulasa....musim pohladat pozri tak za 20 min...
No pockaj skusim ti poslat nieco v ss na Mikulasa....musim pohladat pozri tak za 20 min...
VU UNO openATV, plna skrina kramov
Tento cely prispevok bol napisany bez financnej pomoci EU a tapatalku!
Niektore mimovladky a OZ by mali byt zakazane zo zakona, lebo sluzia len na rozvracanie statov.
Tento cely prispevok bol napisany bez financnej pomoci EU a tapatalku!
Niektore mimovladky a OZ by mali byt zakazane zo zakona, lebo sluzia len na rozvracanie statov.
Re: Bulsatcom 39°E
Tak sv. Mikuláš ti poradil, že máš pomáhať kradnúť?
Hľadám niekoho, kto mi opraví starú poruchanú kosacku
a zavezie jedno dlhe pole hnojom.
Kto do mňa kameňom, ja do neho balvanom.
a zavezie jedno dlhe pole hnojom.
Kto do mňa kameňom, ja do neho balvanom.
Re: Bulsatcom 39°E
Jano neblbni rozbeham mu kartu v prvom rade, to ostatne som nevytvoril ja a pouziva to na vlastne riziko.........ako kazdy.Ako som pisal moze tam mat aj inu chybu,nepozeram tych bulharov, nemam na nich nastaveny tanier.....pekneho Mikulasa aj Tebe.......
VU UNO openATV, plna skrina kramov
Tento cely prispevok bol napisany bez financnej pomoci EU a tapatalku!
Niektore mimovladky a OZ by mali byt zakazane zo zakona, lebo sluzia len na rozvracanie statov.
Tento cely prispevok bol napisany bez financnej pomoci EU a tapatalku!
Niektore mimovladky a OZ by mali byt zakazane zo zakona, lebo sluzia len na rozvracanie statov.
Re: Bulsatcom 39°E
Tak potom díky, ja len na to, že keď si poukazoval neustále na zlodejinu. Takže
Na Mikuláša: Radšej hamovať, ako banovať.
tschüss
Na Mikuláša: Radšej hamovať, ako banovať.
tschüss
Hľadám niekoho, kto mi opraví starú poruchanú kosacku
a zavezie jedno dlhe pole hnojom.
Kto do mňa kameňom, ja do neho balvanom.
a zavezie jedno dlhe pole hnojom.
Kto do mňa kameňom, ja do neho balvanom.
- EnoSat
- Legenda Fóra
- Příspěvky: 2740
- Registrován: 20.únor 2008 - 19:16
- satelitni prijimac: Dreambox - Dr.HD F16 - TBS5925
- Kontaktovat uživatele:
Re: Bulsatcom 39°E
vincek píše:Tak jsem to přepsal ten mg_cfg celý.Pošlu ti to a koukni jestli to mám dobře ale nejde mi to.
Kód: Vybrat vše
# EMM messages
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 01 }
# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 01 }
# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 01 }
# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
# + tps SID, which pmt pid contains au pid
U: { 01 } 0x12c0
# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }
# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
# 32 cccamd netclient, card list saved as /tmp/cccamd.info
# (ECM only, supported server version up to 2.1.1, later not work)
G: { 01 }
# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 07 } 5 30
# network ecm timeout in seconds
K: { 05 }
# newcamd dead routes connect retry, sec
Q: { 60 }
# network shares priority
# 00 gbox, newcamd, cccamd, radegast, camd3 (default)
# 01 camd3, radegast, cccamd, gbox, newcamd
# 02 cccamd, newcamd, camd3, gbox, radegast
P: { 00 }
# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 02 } root dreambox
# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 11 } 80
# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 01 } 192.168.1.50 8025 /tmp/mgcamd.log
# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 00 }
# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E:) time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 04 }
# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 07 }
# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }
# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
# 06 dreambox/mips
# 08 stapi/kathrein
# 09 stapi/ipbox
# 11 stapi/openbox
B: { 00 }
# Mapping 18xx, default is 01
# 00 disable mapping
# 01 map 18xx to 1801
# F: { 00 }
ROVER TAB900+ , Televes H30 FLEX
Gibertini OP100LN /85E-53W/
WaveFrontier T90 /51E-39E-36E-33E-28E-26E-23E-19E-16E-13E-9E-7E-5E-2E-1W-4W/
Edision MIO+ 4K, Octagon SF8008, Mutant HD51, QVIART Lunix, Ustym 4K S2 OTT, VU Solo4K, Dreambox 900UHD/7020HD/500HD, TBS-5925/5530/5220
Gibertini OP100LN /85E-53W/
WaveFrontier T90 /51E-39E-36E-33E-28E-26E-23E-19E-16E-13E-9E-7E-5E-2E-1W-4W/
Edision MIO+ 4K, Octagon SF8008, Mutant HD51, QVIART Lunix, Ustym 4K S2 OTT, VU Solo4K, Dreambox 900UHD/7020HD/500HD, TBS-5925/5530/5220
Re: Bulsatcom 39°E
Nastavení mg_cfg mi jede na skylink ale 39 nejede chyba bude někde jinde.
# EMM messages
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 01 }
# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 01 }
# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 01 }
# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
# + tps SID, which pmt pid contains au pid
U: { 01 } 0x12c0
# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /usr/keys
# 01 files in /tmp
T: { 00 }
# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
# 32 cccamd netclient, card list saved as /tmp/cccamd.info
# (ECM only, supported server version up to 2.1.1, later not work)
G: { 33 }
# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 00 } 5 30
# network ecm timeout in seconds
K: { 10 }
# newcamd dead routes connect retry, sec
Q: { 600 }
# network shares priority
# 00 gbox, newcamd, cccamd, radegast, camd3 (default)
# 01 camd3, radegast, cccamd, gbox, newcamd
# 02 cccamd, newcamd, camd3, gbox, radegast
P: { 00 }
# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 00 } username password
# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 09 } 80
# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 00 } 172.16.1.1 28007 /tmp/mgcamd.log
# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 10 }
# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E:) time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 00 }
# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 00 }
# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }
# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
# 06 dreambox/mips
# 08 stapi/kathrein
# 09 stapi/ipbox
# 11 stapi/openbox
B: { 06 }
# map all 180x nagra caids to 1801
# default is 01
F: { 00 }
# EMM messages
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 01 }
# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 01 }
# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 01 }
# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
# + tps SID, which pmt pid contains au pid
U: { 01 } 0x12c0
# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /usr/keys
# 01 files in /tmp
T: { 00 }
# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
# 32 cccamd netclient, card list saved as /tmp/cccamd.info
# (ECM only, supported server version up to 2.1.1, later not work)
G: { 33 }
# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 00 } 5 30
# network ecm timeout in seconds
K: { 10 }
# newcamd dead routes connect retry, sec
Q: { 600 }
# network shares priority
# 00 gbox, newcamd, cccamd, radegast, camd3 (default)
# 01 camd3, radegast, cccamd, gbox, newcamd
# 02 cccamd, newcamd, camd3, gbox, radegast
P: { 00 }
# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 00 } username password
# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 09 } 80
# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 00 } 172.16.1.1 28007 /tmp/mgcamd.log
# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 10 }
# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E:) time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 00 }
# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 00 }
# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }
# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
# 06 dreambox/mips
# 08 stapi/kathrein
# 09 stapi/ipbox
# 11 stapi/openbox
B: { 06 }
# map all 180x nagra caids to 1801
# default is 01
F: { 00 }
Naposledy upravil(a) vincek dne 06.prosinec 2014 - 15:32, celkem upraveno 1 x.
- EnoSat
- Legenda Fóra
- Příspěvky: 2740
- Registrován: 20.únor 2008 - 19:16
- satelitni prijimac: Dreambox - Dr.HD F16 - TBS5925
- Kontaktovat uživatele:
Re: Bulsatcom 39°E
a co ma nastavenie spolocne s RSA v binarke , pripadne so zlym formatom OP kluca v subore ?vincek píše:Nastavení mi jede ale 39 nejede chyba bude někde jinde.
a kedze si si zakazal debug tak sa to asi ani nedozvies
ROVER TAB900+ , Televes H30 FLEX
Gibertini OP100LN /85E-53W/
WaveFrontier T90 /51E-39E-36E-33E-28E-26E-23E-19E-16E-13E-9E-7E-5E-2E-1W-4W/
Edision MIO+ 4K, Octagon SF8008, Mutant HD51, QVIART Lunix, Ustym 4K S2 OTT, VU Solo4K, Dreambox 900UHD/7020HD/500HD, TBS-5925/5530/5220
Gibertini OP100LN /85E-53W/
WaveFrontier T90 /51E-39E-36E-33E-28E-26E-23E-19E-16E-13E-9E-7E-5E-2E-1W-4W/
Edision MIO+ 4K, Octagon SF8008, Mutant HD51, QVIART Lunix, Ustym 4K S2 OTT, VU Solo4K, Dreambox 900UHD/7020HD/500HD, TBS-5925/5530/5220