hi
Solved by writing the mtd0 file to flash again

regards

there is some news here , i could using usbupg command uploading the usb_uboot.img file( for the sf918+ included in the backup folder of the startkit)to my receiver , here is the output on startup ' Îs NAND read: device 0 offset 0x500000, size 0x300000 Reading data from 0x7ff800 -- 100% complete. 31...

Hello ,

Thanks for the answer and sorry for the delay ;
This is the problem , there is no way to load anything with this u-boot on board ; CH UP doesn't work . So the only way i think is to write the correcte file ( u-boo) on nand flash with commands line
Regards

hello ; Wanting to install E2 on my fortis box hs 7819 I introduced , by mistake, a U_Boot which is for hs77119 and I am now stuck with this : :dash: Board: STx7111-7119 [32-bit mode] U-Boot 1.3.1 (Nov 16 2013 - 09:55:12) - stm23_0046 DRAM: 256 MiB NAND: 256 MiB *** Warning - bad CRC or NAND, using ...

hello ;

No need to change anything , just HDReady installed and OScam works well !!!!

thanks once again

Regards

hello

not need to be sorry .
I can see in this topic that is an hdready Enigma for 7819 , i'll tray to install it ; if there is same probleme i'll tray instructions given above . may be that solve my case . We'll see .

thanks for your time

Regards

the Box is hs7819 , E2 HDBOX PLATINO 9105+:~# uname -a Linux 9105+ 2.6.32.28_stm24_0207 #2 PREEMPT Sat Feb 9 17:44:57 CET 2013 sh4 GNU Linux 9105+:~# cat /proc/cpuinfo machine : sat7111 processor : 0 cpu family : sh4 cpu type : STx7111 cut : 3.x cpu flags : fpu icbi synco fpchg cache type : split (h...

image installed again , there is no rules file
only MAKEDEV exist in /sbin/ . Regards

sorry it's my fault for not mentioning the whole output ; the box is in original SW now , but the output of the command look like : crw--w---- 1 root root ........ /dev/ttyAS0. i guess the owner is root and the group is root also concerning the udev rule , where can i set this line , because there i...

yeh of course , it's for using OScam with serial prtotcol on E2 platino , the same binary and config work well on other E2 sh4 , but not on Platino . when i make ls -l /dev/ttyAS0 i can see crw--w---- ; same command in other image give crw-rw---- as you can see the group can read from the device als...

thanks for replay , unfortunatly not ; here is th output mount: mounting /dev/ttyAS0 on /mnt/serial failed: Block device required I've read in an other forum ,same subject : As far as i know you cant mount this tty things you could connect via minicom or any other software which works on this serial...

Does it work if I use an USB -serial adapter ??

noway to get answer here !!!!

hello ,

Is it possible to change permanently , the /dev/ttyAS0 permissions from 620 to 660 ? if so how to di it ??

Regards

i guess there is no one use this image anymore

bR

hello ; I would like to use OScam with serial protocol on this image , in my 7819 box, but it doesn't work , same config and same binary work fine in other image as PKT or HDMU even in E2 own build from max-tdt git's but not in HDBOX Platino . Can some one give an explanation or how to solve this po...