[HELP]: Wrong u_boot into flash

[ch@os_73]

hello ;

Wanting to install E2 on my fortis box hs 7819 I introduced , by mistake, a U_Boot which is for hs77119 and I am now stuck with this :

Kód: Vybrat vše

Board: STx7111-7119  [32-bit mode]

U-Boot 1.3.1 (Nov 16 2013 - 09:55:12) - stm23_0046

DRAM:  256 MiB
NAND:  256 MiB
*** Warning - bad CRC or NAND, using default environment

In:	serial
Out:   serial
Err:   serial
set ethaddr 00:1e:b8:0a:ae:a3
done
Setup mac address.
done
Hit any key to stop autoboot:  0
(Re)start USB...
USB:   scanning bus for devices... 2 USB Device(s) found
   	scanning bus for storage devices... 0 Storage Device(s) found
** Can't read from device 0 **

** Unable to use usb 0:1 for fatload **
## Booting image at 80000000 ...
Bad Magic Number

NAND read: device 0 offset 0x60000, size 0x300000

reading NAND page at offset 0x60000 failed
 3145728 bytes read: ERROR
## Booting image at 80000000 ...
Bad Magic Number
7119 >

I tried to load the correct one given in startkit7819( usb_uboot.img for hs7819) using CH UP method but noway ; log :

Kód: Vybrat vše

 Board: STx7111-7119  [32-bit mode]

U-Boot 1.3.1 (Nov 16 2013 - 09:55:12) - stm23_0046

DRAM:  256 MiB
NAND:  256 MiB
*** Warning - bad CRC or NAND, using default environment

In:	serial
Out:   serial
Err:   serial
set ethaddr 00:1e:b8:0a:ae:a3
done
Setup mac address.
done
Hit any key to stop autoboot:  0
(Re)start USB...
USB:   scanning bus for devices... 3 USB Device(s) found
   	scanning bus for storage devices... 1 Storage Device(s) found
reading uImage

** Unable to read "uImage" from usb 0:1**
## Booting image at 80000000 ...
Bad Magic Number

NAND read: device 0 offset 0x60000, size 0x300000

reading NAND page at offset 0x60000 failed
 3145728 bytes read: ERROR
## Booting image at 80000000 ...
Bad Magic Number
7119 >

I have a copy saved of partition /dev/mtd0 that i have make previously .

Kód: Vybrat vše

 dev:	size   erasesize  name
mtd0: 00400000 00020000 "boot"

How can i solve this ? any help please .

Regards

[Bohulka]

Hi first give back the start kit. usb_uboot .. Try to install the official IRD image. Official IRD img FAC.Skytec HD.KLEIO.CIP.Dev.2.11.72.2013Oct10 let one piece boot basic settings. Then install Startkit_kleio_20131122. More information can be found on http://www.forum.techneteuweb.eu

[ch@os_73]

Hello ,

Thanks for the answer and sorry for the delay ;
This is the problem , there is no way to load anything with this u-boot on board ; CH UP doesn't work . So the only way i think is to write the correcte file ( u-boo) on nand flash with commands line
Regards

[revis]

uboot na mutliuboot funguje len na dvoch starsich verziach fw . teda upgrade, nasledne sa nainstalovanim najnovsej verzie uz neprepise, ostane funkcny ako multiuboot uz stale.
Prepisovacia verzia je :
2.11.34
2.11.49
2.11.53

Novsie verzie fw to uz nedokazu .

[ch@os_73]

there is some news here , i could using usbupg command uploading the usb_uboot.img file( for the sf918+ included in the backup folder of the startkit)to my receiver , here is the output on startup

Kód: Vybrat vše

' Îs

NAND read: device 0 offset 0x500000, size 0x300000

Reading data from 0x7ff800 -- 100% complete.
 3145728 bytes read: OK
Bad Magic Number
HDK7111>

also I could confirm with "sscom32" connected that the reseller id in now is 27 01 00 A0 ; do you think that i can upgrade using porter loader the last octagon 918gse+ SW without risk ? Or mybe should i use a reseller changer to change 1008GSE+ to 00 A0 and then load it to the box to get the correct loader in when the next restart .

regards

[ch@os_73]

hi
Solved by writing the mtd0 file to flash again

regards