WL500gP svn55xx problem s log suborom

[PeterKt]

Ahojte!

Pri pouziti oscam-svn55XX-mips-wrt54g binariek je problem s oscam.log suborom v tom, ze sa log nabaluje do velkosti aj 16MB. Oscam neakceptuje nastavenie maxlogsize = xx, ani nastavenie maxlogsize cez webif. Stretli ste sa s tym niekto? Pomoze len disablelog = 1.

Vratil som sa preto k binarke oscam-svn5477-openwrt-little_endian-kernel26, kde nastavenia oscam.conf a aj cez webif oscam akceptuje.

Je skoda, ze v distribucia light-Distribution uz neobsahuje openwrt-little_endian binarky ale binarky mips-wrt54g, pri ktorych tieto problemy pretrvavaju.

[mjozef]

A skusal niekdo tento

[PeterKt]

To je binarka, ktora funguje perfektne. Myslim, ze ju vytvoril dolehaj na cssf. Je tam publikovana aj s dalsimi, napr. pre router TPlink.

[DuoCore]

Stahuji binárky odsud, máte zkušenosti ?

http://download.oscam.to/index.php?PHPS ... ips-wrt54g

[revis]

Ja odtial taham tiez binarky. Potrebna registracia (pred mesiacom este nebola) .
maju aj dobre forum .

[thom4s]

Mate niekto rozbehanu citacku SMARGO PLUS (origo, ziadny klon FW 1.5)
v kombinacii WL-500GP v2 , OpenWRT Backfire 10.3.1-RC6
+ oscam-svn5648-ASUSWL-LIBUSB-WEBIF ???

Citacka nechce ani zanic nacitat 0d03 kartu.

Driver si myslim ze nema problem.

usbserial: USB Serial Driver core
usbcore: registered new interface driver ftdi_sio
usb 3-2: new full speed USB device using uhci_hcd and address 2
usb 3-2: configuration #1 chosen from 1 choice
usb 3-2: Detected FT232BM
usb 3-2: Number of endpoints 2
usb 3-2: Endpoint 1 MaxPacketSize 64
usb 3-2: Endpoint 2 MaxPacketSize 64
usb 3-2: Setting MaxPacketSize 64
usb 3-2: FTDI USB Serial Device converter now attached to ttyUSB0


Log pri nastaveni Smargo plus citacky:

[reader]
label = smargocitacka
protocol = smargo
device = /dev/ttyUSB0
device_out_endpoint = 0x82
services = 0d03,vsetko
caid = 0D03
detect = none
mhz = 369
cardmhz = 369
group = 1,2,3
emmcache = 1,3,2

2012/02/07 16:17:55 1005 r reader thread started (thread= 1005, label=smargocitacka, device=/dev/ttyUSB0, detect=none, mhz=369, cardmhz=369)
2012/02/07 16:17:55 1005 r smargo init
2012/02/07 16:17:55 400 s loadbalancer: can't read from file /tmp/.oscam/stat
2012/02/07 16:17:55 400 s waiting for local card init
2012/02/07 16:17:56 1005 r smargocitacka card detected
2012/02/07 16:18:04 1005 r ATR: A0 18
2012/02/07 16:18:04 1005 r ERROR: Could not read reader->convention
2012/02/07 16:18:04 1005 r Error activating card.
2012/02/07 16:18:12 1005 r ATR: A0 18
2012/02/07 16:18:12 1005 r ERROR: Could not read reader->convention
2012/02/07 16:18:12 1005 r Error activating card.
2012/02/07 16:18:20 1005 r ATR: A0 18
2012/02/07 16:18:20 1005 r ERROR: Could not read reader->convention
2012/02/07 16:18:20 1005 r Error activating card.
2012/02/07 16:18:21 1005 r card initializing error
2012/02/07 16:18:21 400 s init for all local cards done
2012/02/07 16:18:21 400 s anti cascading disabled


Log pri nastaveni Smargo plus citacky:

[reader]
label = smargocitacka
protocol = smartreader
device = 003:0002
device_out_endpoint = 0x82
services = 0d03,vsetko
caid = 0D03
detect = none
mhz = 369
cardmhz = 369
group = 1,2,3
emmcache = 1,3,2


2012/02/07 16:26:47 1005 r reader thread started (thread= 1005, label=smargocitacka, device=003:0002, detect=none, mhz=369, cardmhz=369)
2012/02/07 16:26:47 400 s loadbalancer: can't read from file /tmp/.oscam/stat
2012/02/07 16:26:47 400 s waiting for local card init
2012/02/07 16:26:47 1005 r Using 0x82 as endpoint for smartreader hardware detection
2012/02/07 16:26:47 1005 r Found smartreader device 003:0002
2012/02/07 16:26:48 1005 r smargocitacka card detected