ASUS WL 500 gp

[rsevcik]

Teď sice nevím z hlavy jaká je cesta ke čtečce v XWRt pro jistotu prověř a zkontroluj. Jinak si ještě dej každou čtečku do jiné group, myslím si že je to rozumnější. Ještě zkus toto detect = cd. Třeba se ti zadaří.

[juuiicee]

Zmena Group + detect=cd nic nezmenila situace stale stejna

[rsevcik]

Tu cestu ke čtečce si prověřil (/dev/ttyUSB1) ? Jinak čtečky máš opravdu v módu mouse? Ještě jsem něco staršího našel to nastavení by mohlo vypadat asi takto
label = xxx
enable = 1
protocol = mouse
device = /dev/ttyUSB0
device_out_endpoint = 0x81
services =
caid = 0D0F
detect = none
mhz = 357
cardmhz = 357
ident =
group = 1
emmcache = 1,3,2
lb_weight = 100
deprecated = 1
Ještě tu třeba něco ke čtečce http://www.ab-forum.info/viewtopic.php? ... &start=980

[rsevcik]

Ještě tady nějaké info i obr. http://www.ab-forum.info/index.php

[alfsvk]

Neviem ci nehonite ducha, ZDK citacka a oscam chodi dobre len v K 2.6.
Citacku treba mat v mode PHOENIX.

[rosssss]

...kde najdu binarky oscamu od dolehaj?

dik

[alfsvk]

http://www.ab-forum.info/viewtopic.php?p=399060#p399060

[681010]

[jumbo]

Neviem ci nehonite ducha, ZDK citacka a oscam chodi dobre len v K 2.6.
Citacku treba mat v mode PHOENIX.

Já mám ZDK čtečku v K 2.6 Čtečku mám v modu mouse a vše šlape 0D03,0D96,0624. V modě phoenix mě nešlo nic.Ubuntu 10.10 Oscam mám 6016.Tak nechápu že někomu to jede v modu Phoenix a někomu v mouse.

[alfsvk]

FTDi driver pre ubuntu asi nebude indenticky s ASUSovym. A ono je to cele o driveroch. Smouse a phoenix sa lisia nabeznou a zostupnou hranou. U newcs sa to dalo poriesit parametrom reset inverse.
Schvalne som teraz pozrel na RT-N16 s DD-WRT a mam tam phoenix mod.

[PeterKt]

Presne tak, pre asus routre s dostupnymi ovladacmi je potrebne mat ZDK dvojcitacku v mode phoenix ak chcete pouzivat oscam, inak oscam nenainicializuje karty v citacke.

Na ubuntu to samozrejme moze byt uplne inak. Preto mam ZDK dvojku s moznostou prepnutia modu pomocou jumpers - rovnakymi ako su na prepnutie frekvencie 3,57/6

[PeterKt]

Ak niekto nevie ci ma ZDK v rezime phoenix, alebo mouse, tak v prilohe je obrazok na vysvetlenie. Uz to tu sice bolo, ale obcas nezaskodi si to zopaknut. Obrazok je prevzaty z cssf.

[thomash1]

novy oscam pro Asuse-oleg

[juuiicee]

Asus wl-500gp + Oleg FW + oscam 5648 + dvojctecka ZDK phoenix + Cryptoworks (mhz i cardmhz = 357MHz)

Odezva karty v oscamu 400-800ms předtím to běželo na Dreamboxu 500s a tam byla odezva 100-300ms Je tak vysoká odezva normální nebo se s tím dá něco udělat? Kolik je mezní odezva?

[morphy32]

Zdravim,
ano ta odozva je normalna. Ja mam bezne 430, pod to to snad nikdy nekleslo.

[jumbo]

Je to normální.Někdy to naběhne i na 800 ms

[asconn]

Ahoj,
nahrál jsem do svého Asus WL-500G Premium v1 Open WRT Kamikaze verze r4743, dále oscam dle návodu

Kód: Vybrat vše

http://ab-forum.info/viewtopic.php?p=338143#p338143

a webrozhraní oscamu mi stále hlásí toto

Kód: Vybrat vše

1970/01/01 1:00:28 400 s creating thread for device /dev/ttyUSB0
1970/01/01 1:00:28 1005 r reader thread started (thread= 1005, label=int_0d0f, device=/dev/ttyUSB0, detect=none, mhz=357, cardmhz=357)
1970/01/01 1:00:28 1005 r ERROR opening device /dev/ttyUSB0
1970/01/01 1:00:28 1005 r Cannot open device: /dev/ttyUSB0
1970/01/01 1:00:28 400 s loadbalancer: can't read from file /tmp/.oscam/stat
1970/01/01 1:00:28 400 s waiting for local card init
2012/04/03 8:16:08 1005 r ERROR opening device /dev/ttyUSB0
2012/04/03 8:16:08 1005 r Cannot open device: /dev/ttyUSB0
2012/04/03 8:17:08 1005 r ERROR opening device /dev/ttyUSB0

na dmesg dostávám toto:

Kód: Vybrat vše

root@OpenWrt:~# dmesg
Linux version 2.6.25.17 (buildbot@localhost.localdomain) (gcc version 4.1.2) #1 Tue Apr 28 06:00:05 CDT 2009
console [early0] enabled
CPU revision is: 00029006 (Broadcom BCM3302)
ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x03, vendor 0x4243)
ssb: Core 1 found: Fast Ethernet (cc 0x806, rev 0x06, vendor 0x4243)
ssb: Core 2 found: Fast Ethernet (cc 0x806, rev 0x06, vendor 0x4243)
ssb: Core 3 found: USB 1.1 Hostdev (cc 0x808, rev 0x02, vendor 0x4243)
ssb: Core 4 found: PCI (cc 0x804, rev 0x08, vendor 0x4243)
ssb: Core 5 found: MIPS 3302 (cc 0x816, rev 0x00, vendor 0x4243)
ssb: Core 6 found: V90 (cc 0x807, rev 0x02, vendor 0x4243)
ssb: Core 7 found: IPSEC (cc 0x80B, rev 0x00, vendor 0x4243)
ssb: Core 8 found: MEMC SDRAM (cc 0x80F, rev 0x00, vendor 0x4243)
ssb: Initializing MIPS core...
ssb: set_irq: core 0x0806, irq 2 => 2
ssb: set_irq: core 0x0806, irq 3 => 3
ssb: set_irq: core 0x0804, irq 0 => 4
ssb: Sonics Silicon Backplane found at address 0x18000000
Serial init done.
Determined physical RAM map:
 memory: 02000000 @ 00000000 (usable)
Entering add_active_range(0, 0, 8192) 0 entries of 256 used
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal          0 ->     8192
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->     8192
On node 0 totalpages: 8192
  Normal zone: 64 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 8128 pages, LIFO batch:0
  Movable zone: 0 pages used for memmap
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 init=/etc/preinit noinitrd console=ttyS0,115200
Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Synthesized clear page handler (26 instructions).
Synthesized copy page handler (46 instructions).
PID hash table entries: 128 (order: 7, 512 bytes)
console handover: boot [early0] -> real [ttyS0]
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 29808k/32768k available (2082k kernel code, 2960k reserved, 315k data, 128k init, 0k highmem)
Calibrating delay loop... 263.16 BogoMIPS (lpj=526336)
Mount-cache hash table entries: 512
net_namespace: 540 bytes
NET: Registered protocol family 16
Switched to high resolution mode on CPU 0
ssb: PCIcore in host mode found
Registering a PCI bus after boot
PCI: Fixing up bridge 0000:00:00.0
PCI: Setting latency timer of device 0000:00:00.0 to 64
PCI: Fixing up device 0000:00:00.0
PCI: Fixing latency timer of device 0000:00:00.0 to 168
PCI: Enabling device 0000:00:02.0 (0000 -> 0002)
PCI: Fixing up device 0000:00:02.0
PCI: Setting latency timer of device 0000:00:02.0 to 64
ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0D, vendor 0x4243)
ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor 0x4243)
ssb: Core 2 found: PCI (cc 0x804, rev 0x0C, vendor 0x4243)
ssb: Core 3 found: PCMCIA (cc 0x80D, rev 0x07, vendor 0x4243)
ssb: SPROM revision 2 detected.
ssb: Sonics Silicon Backplane found on PCI device 0000:00:02.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
detected lzma initramfs
initramfs: LZMA lc=1,lp=2,pb=2,origSize=512
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  Š 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 3) is a 16550A
serial8250 serial8250.0: unable to register port at index 0 (IO0 MEMb8000300 IRQ3): -28
serial8250 serial8250.0: unable to register port at index 1 (IO0 MEMb8000400 IRQ3): -28
b44.c:v2.0
eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:18:f3:98:e0:e6
b44: eth1: PHY Reset would not complete.
eth1: Broadcom 44xx/47xx 10/100BaseT Ethernet 40:10:18:00:00:2d
flash init: 0x1c000000 0x02000000
Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
 Amd/Fujitsu Extended Query Table at 0x0040
Physically mapped flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Flash device: 0x800000 at 0x1fc00000
bootloader size: 262144
Creating 4 MTD partitions on "Physically mapped flash":
0x00000000-0x00040000 : "cfe"
0x00040000-0x007f0000 : "linux"
0x000fe400-0x007f0000 : "rootfs"
mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=270000, len=580000
0x00270000-0x007f0000 : "rootfs_data"
0x007f0000-0x00800000 : "nvram"
TCP vegas registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 128k freed
Please be patient, while OpenWrt loads ...
Algorithmics/MIPS FPU Emulator v1.5
diag: Detected 'ASUS WL-500g Premium'
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
roboswitch: Probing device eth0: found!
b44: eth0: powering down PHY
mini_fo: using base directory: /
mini_fo: using storage directory: /jffs
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
b43-phy0: Broadcom 4318 WLAN found
b43-phy0 debug: Found PHY: Analog 3, Type 2, Revision 7
b43-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 8
b43-phy0 debug: DebugFS (CONFIG_DEBUG_FS) not enabled in kernel config
phy0: Selected rate control algorithm 'pid'
Broadcom 43xx driver loaded [ Features: NLR, Firmware-ID: FW13 ]
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
USB Universal Host Controller Interface driver v3.0
PCI: Enabling device 0000:00:03.0 (0000 -> 0001)
PCI: Fixing up device 0000:00:03.0
uhci_hcd 0000:00:03.0: UHCI Host Controller
uhci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:03.0: irq 6, io base 0x00000100
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
PCI: Enabling device 0000:00:03.1 (0000 -> 0001)
PCI: Fixing up device 0000:00:03.1
uhci_hcd 0000:00:03.1: UHCI Host Controller
uhci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:03.1: irq 6, io base 0x00000120
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
PCI: Enabling device 0000:00:03.2 (0000 -> 0002)
PCI: Fixing up device 0000:00:03.2
ehci_hcd 0000:00:03.2: EHCI Host Controller
ehci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:03.2: irq 6, io mem 0x40002000
usb 1-1: new full speed USB device using uhci_hcd and address 2
ehci_hcd 0000:00:03.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
hub 1-0:1.0: unable to enumerate USB device on port 1
hub 3-0:1.0: unable to enumerate USB device on port 1
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver ftdi_sio
drivers/usb/serial/ftdi_sio.c: v1.4.3:USB FTDI Serial Converters Driver
usb 1-1: new full speed USB device using uhci_hcd and address 3
usb 1-1: device descriptor read/64, error -88
usb 1-1: device descriptor read/64, error -88
usb 1-1: new full speed USB device using uhci_hcd and address 4
usb 1-1: device descriptor read/64, error -88
usb 1-1: device descriptor read/64, error -88
usb 1-1: new full speed USB device using uhci_hcd and address 5
usb 1-1: device not accepting address 5, error -88
usb 1-1: new full speed USB device using uhci_hcd and address 6
usb 1-1: device not accepting address 6, error -88
hub 1-0:1.0: unable to enumerate USB device on port 1
usbcore: deregistering interface driver ftdi_sio
drivers/usb/serial/usb-serial.c: USB Serial deregistering driver FTDI USB Serial Device
usbcore: deregistering interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial deregistering driver generic
usbcore: deregistering interface driver usbserial
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver ftdi_sio
drivers/usb/serial/ftdi_sio.c: v1.4.3:USB FTDI Serial Converters Driver
root@OpenWrt:~#

oscam.log

Kód: Vybrat vše

-------------------------------------------------------------------------------
>> OSCam <<  cardserver started at Thu Jan  1 01:00:27 1970
-------------------------------------------------------------------------------
1970/01/01  1:00:27      400 s >> OSCam <<  cardserver started version 1.00-unstable_svn, build #4803 (mips-wrt54g-linux)
1970/01/01  1:00:27      400 s version=1.00-unstable_svn, build #4803, system=mips-wrt54g-linux, nice=-1
1970/01/01  1:00:27      400 s client max. idle=120 sec, debug level=0
1970/01/01  1:00:27      400 s max. logsize=30 Kb
1970/01/01  1:00:27      400 s client timeout=3000 ms, fallback timeout=2500 ms, cache delay=0 ms
1970/01/01  1:00:27      400 s auth size=4976
1970/01/01  1:00:27      400 s services reloaded: 0 services freed, 12 services loaded
1970/01/01  1:00:27      400 s userdb reloaded: 1 accounts loaded, 0 expired, 0 disabled
1970/01/01  1:00:27      400 s signal handling initialized (type=sysv)
1970/01/01  1:00:28      400 s 8929 service-id's loaded
1970/01/01  1:00:28      400 s can't open file "/jffs/oscam/bin/oscam.tiers" (err=2), no tier-id's loaded
1970/01/01  1:00:28      400 s can't open file "/jffs/oscam/bin/oscam.provid" (err=2), no provids's loaded
1970/01/01  1:00:28      400 s can't open file "/jffs/oscam/bin/oscam.ird" (errno=2) irdeto guessing not loaded
1970/01/01  1:00:28      400 s monitor: initialized (fd=10, port=10000)
1970/01/01  1:00:28      400 s camd33: disabled
1970/01/01  1:00:28      400 s camd35: disabled
1970/01/01  1:00:28      400 s cs378x: disabled
1970/01/01  1:00:28      400 s newcamd: initialized (fd=11, port=10010, crypted)
1970/01/01  1:00:28      400 s CAID: 0D0F
1970/01/01  1:00:28      400 s provid #0: 000004
1970/01/01  1:00:28      400 s provid #1: 000008
1970/01/01  1:00:28      400 s provid #2: 00000C
1970/01/01  1:00:28      400 s provid #3: 000010
1970/01/01  1:00:28      400 s newcamd: initialized (fd=12, port=10011, crypted)
1970/01/01  1:00:28      400 s CAID: 0D96
1970/01/01  1:00:28      400 s provid #0: 000004
1970/01/01  1:00:28      400 s provid #1: 000008
1970/01/01  1:00:28      400 s newcamd: initialized (fd=13, port=10012, crypted)
1970/01/01  1:00:28      400 s CAID: 0D02
1970/01/01  1:00:28      400 s provid #0: 00008C
1970/01/01  1:00:28      400 s provid #1: 0000A0
1970/01/01  1:00:28      400 s provid #2: 0000A4
1970/01/01  1:00:28      400 s provid #3: 0000A8
1970/01/01  1:00:28      400 s cccam: initialized (fd=14, port=12000, crypted)
1970/01/01  1:00:28      400 s radegast: disabled
1970/01/01  1:00:28      C04 h HTTP Server listening on port 8888
1970/01/01  1:00:28      400 s http thread started
1970/01/01  1:00:28      400 s creating thread for device /dev/ttyUSB0
1970/01/01  1:00:28     1005 r reader thread started (thread=    1005, label=int_0d0f, device=/dev/ttyUSB0, detect=none, mhz=357, cardmhz=357)
1970/01/01  1:00:28     1005 r ERROR opening device /dev/ttyUSB0
1970/01/01  1:00:28     1005 r Cannot open device: /dev/ttyUSB0
1970/01/01  1:00:28      400 s loadbalancer: can't read from file /tmp/.oscam/stat
1970/01/01  1:00:28      400 s waiting for local card init

Čtečku mám Smargo SmartReader a je zasunuta ve spodním USB. Zkoušel jsem protokol nastavit na mouse i phoenix a žádná změna. Nebyl by tu nějaký mírumilovný člověk, který by nahodil udičku?

[bbedo2]

ak mozem otazku mimo temu
poradi niekto ako zapnut/vypnut wifi bez toho aby sa musel rooter restartovat?
ked dam cez webove rozhranie iba finish tak sa nic nestane

[morphy32]

1970/01/01 1:00:28 1005 r reader thread started (thread= 1005, label=int_0d0f, device=/dev/ttyUSB0, detect=none, mhz=500, cardmhz=357)

Daj v nastaveni citacky 357 mhz a card mhz 357

[asconn]

Čtečku jsem dal zpět na 357 a žádná změna.