TP-Link TL-WR1043ND

[Stanowi94]

je tam s atributama 755

[alfsvk]

NIC?

[Stanowi94]

routr restartován a stále nic..

[marecek29]

Dnes jsem musel preinstalovat tplinka.
Pri pokusu o instalci to hodi:
Downloading http://downloads.openwrt.org/backfire/1 ... ackages.gz.
wget: bad address 'downloads.openwrt.org'Collected errors:*opkg_download: Failed to download http://downloads.openwrt.org/backfire/1 ... ackages.gz, wget returned 1.
Internet pres to jede.V openwrt-diagnostic-ping: bad address 'openwrt.org'.
V opere se na : http://downloads.openwrt.org/backfire/1 ... x/packages dostanu.
Nevi nekdo co s tim? Uz jsem to delal nekolikrat a nikdy nebyl problem.

[Stanowi94]

Ahojte Potřebuji všechny porty které TP-link má, do wanu mám přívod kde je nastaveno DHCP, dá se něják nastavit aby lan brala taky tohle DHCP ?

[plesi]

Dnes jsem musel preinstalovat tplinka.
Pri pokusu o instalci to hodi:
Downloading http://downloads.openwrt.org/backfire/1 ... ackages.gz.
wget: bad address 'downloads.openwrt.org'Collected errors:*opkg_download: Failed to download
Nevi nekdo co s tim? Uz jsem to delal nekolikrat a nikdy nebyl problem.

Protoze mas spatnou adresu.
Spatne:

Kód: Vybrat vše

http://downloads.openwrt.org/backfire/10.03.1-rc6/ar71xxpackages/Packages.gz

spravne:

Kód: Vybrat vše

http://downloads.openwrt.org/backfire/10.03.1-rc6/ar71xx/packages/Packages.gz

Chyba je ta,ze ti zde: /ar71xxpackages/
chybi lomitko [/]

Spravne to je:
/ar71xx/packages/

[marecek29]

Vyreseno.Dik.

[teapack]

edit: vyriešené

[marecek29]

Podle navodu je adresa 168.168.1.1 a jede jenom telnet.

[koenzim]

Zdravim. Snazim sa rozbehnut Oscam na tomto routri, ale mam problem s nacitanim karty.

Kód: Vybrat vše

2012/08/12 13:23:44 5B96D0 r mouse [mouse] Reader initialized (device=/dev/ttyUSB0, detect=cd, mhz=500, cardmhz=357) 
2012/08/12 13:23:44 5B96D0 r mouse [mouse] card detected 
2012/08/12 13:23:55 5B96D0 r mouse [mouse] Error activating card. 
2012/08/12 13:23:59 5B96D0 r ATR is malformed, it reports 8 historical bytes but there are only 0 
2012/08/12 13:24:00 5B96D0 r mouse [mouse] ATR: 3B 78 00 3B 78 
2012/08/12 13:24:03 5B96D0 r mouse [mouse] Warning: D=0 is invalid, forcing D=1 
2012/08/12 13:24:05 5B96D0 r mouse [mouse] Maximum frequency for this card is formally 4 Mhz, clocking it to 5.00 Mhz 
2012/08/12 13:24:06 5B96D0 r mouse [mouse] card system not supported 
2012/08/12 13:24:06 5B96D0 r mouse [mouse] Normal mode failed, reverting to Deprecated Mode 
2012/08/12 13:24:16 5B96D0 r mouse [mouse] Error activating card. 
2012/08/12 13:24:21 5B96D0 r ATR is malformed, it reports 8 historical bytes but there are only 0 
2012/08/12 13:24:22 5B96D0 r mouse [mouse] ATR: 3B 78 00 3B 78 
2012/08/12 13:24:22 5B96D0 r mouse [mouse] Warning: D=0 is invalid, forcing D=1 
2012/08/12 13:24:23 5B96D0 r mouse [mouse] Maximum frequency for this card is formally 5 Mhz, clocking it to 5.00 Mhz 
2012/08/12 13:24:24 5B96D0 r mouse [mouse] card system not supported 
2012/08/12 13:24:24 5B96D0 r mouse [mouse] card initializing error 
2012/08/12 13:24:24 0 s init for all local cards done 
2012/08/12 13:24:24 0 s anti cascading disabled 

Skusal som zadat ATR napevno (skopirovane z oscamu z Anacondy, kde karta funguje), vtedy to prejde takto:

Kód: Vybrat vše

2012/08/12 13:31:09 5B96D0 r mouse [mouse] card detected 
2012/08/12 13:31:09 5B96D0 r mouse [mouse] Using ATR from reader config 
2012/08/12 13:31:09 5B96D0 r mouse [mouse] ATR: 3B 78 12 00 00 A0 C4 06 07 8F F1 90 00 
2012/08/12 13:31:14 5B96D0 r mouse [mouse] Maximum frequency for this card is formally 5 Mhz, clocking it to 5.00 Mhz 
2012/08/12 13:31:15 5B96D0 r mouse [mouse] card detected 
2012/08/12 13:31:15 5B96D0 r mouse [mouse] type: CryptoWorks 
2012/08/12 13:31:18 5B96D0 r mouse [mouse] card system not supported 
2012/08/12 13:31:18 5B96D0 r mouse [mouse] Normal mode failed, reverting to Deprecated Mode 
2012/08/12 13:31:18 5B96D0 r mouse [mouse] Using ATR from reader config 
2012/08/12 13:31:18 5B96D0 r mouse [mouse] ATR: 3B 78 12 00 00 A0 C4 06 07 8F F1 90 00 
2012/08/12 13:31:19 5B96D0 r mouse [mouse] Maximum frequency for this card is formally 5 Mhz, clocking it to 5.00 Mhz 
2012/08/12 13:31:20 5B96D0 r mouse [mouse] card detected 
2012/08/12 13:31:20 5B96D0 r mouse [mouse] type: CryptoWorks 
2012/08/12 13:31:23 5B96D0 r mouse [mouse] card system not supported 
2012/08/12 13:31:23 5B96D0 r mouse [mouse] card initializing error

oscam.conf

Kód: Vybrat vše

[global]
logfile                       = /tmp/oscam.log
disablelog                    = 0
disableuserfile               = 0
usrfileflag                   = 0
clienttimeout                 = 5000
fallbacktimeout               = 2500
clientmaxidle                 = 120
cachedelay                    = 120
bindwait                      = 120
netprio                       = 0
clientdyndns                  = 0
resolvedelay                  = 30
unlockparental                = 0
nice                          = 1
serialreadertimeout           = 1500
maxlogsize                    = 10
waitforcards                  = 1
preferlocalcards              = 0
saveinithistory               = 1
readerrestartseconds          = 5
readerautoloadbalance         = 0
readerautoloadbalance_save    = 0

oscam.server

Kód: Vybrat vše

[reader]
label                         = mouse
protocol                      = mouse
device                        = /dev/ttyUSB0
atr                           = 3B78120000A0C406078FF19000
detect                        = cd
mhz                           = 500
cardmhz                       = 357
group                         = 1
emmcache                      = 1,1,2

[koenzim]

Vsetci su na dovolenke, nikto nevie poradit?

[vprint]

Treba skusat skusat, napr. detect - none, frekv daj obe na 357 apod.

[reavis]

zdravim, chcem sa opytat aka sa da pouzit citacka co sa da este kupit, tu spominane nemozem zohnat,

vdaka za radu

[dragunik]

Mam odskusanu tuto 4v1 Phoenix, smartMouser

[iiggii]

zdravim, chcem sa opytat aka sa da pouzit citacka co sa da este kupit, tu spominane nemozem zohnat,

vdaka za radu

http://www.ab-forum.info/viewtopic.php? ... 13#p434913

[reavis]

Mam odskusanu tuto 4v1 Phoenix, smartMouser

vdik za radu, objednal som toho phoenixa

[reavis]

zdravím,
potreboval by som poradit, rozbiehal som tplink router, nieco som zmenil na wlan s lan, uz sa mi nedalo pripojit, ip som si v nom zmenil na inu, ako ma router co ide do netu, a teraz sa vobec nemozem do neho dostat, resetoval som ho najskor tlacitkom co je vzadu na routri, potom som vyskusal aj putty cez telnet, aj total comander cez ftp, vobec sa nemozem dostat do neho, ked sa pozriem v routri , stale vidim na nom ip, ktoru som si tam na zaciatku zadal, program putty ako spustim, stlacim QSS, zacen rychlejsie blikat, zadam ip 192.168.1.1 mod telnet a dam otvorit, hned sa mi sam zatvori, menil som aj wlan a lan , prehadzovat kabel, skusal som navody co su v tomto vlakne, a nic, neviete co by som z tym este mohol urobit , aby som sa dostal do neho ? vdik za rady

[dragunik]

Vypni ho, propoj sa don len s PC tak ako prvy krat a zadaj tu novu IP.

[reavis]

tak podarilo sa , na druhom pc, nechal som to vypnute celu noc, vdik

[reavis]

zdravim, potreboval by som poradit, lebo neche mi na routri ist vobec net, mam router z wifi, kde mam net, nat som z lan pripojil tplink , mam pevnu IP na routri ktory pouzivam s wifi,
mam to zapojene PC - router - tplink

ked dam z toho routra do TP linku cez lan kabel , nacitam ho v pc cez ip, ktoru nieje rovnaka ako v routri(192.168.1.1 - ma router)

ked dam do WAN vobec ho nevidim, neviem si dat rady ako nastavit openWRT v TPL linku a co v routri, router mi ho vidi , dal som mu aj prioriry MAc adresy TP linku , sksual som a nemozem nic najst podla coho by som to rozbehal,

vdik za radu