ODPALENA FLASH PAMAT? heeelp

[Peter_z_BB]

Dobry vecer,

no mam optibox anaconda plus (cize ako 9105+). Po neuspesnom flashovani enigmy 2 "E2 9105+
Nebula V3 image PKT", mi prijimac postupuje nasledovne. LD 7.36, LODAING USB - ak mam kluc s
enigmou, LOADING, potom START, ak je enigma tak RUN , no a uz nic len svieti cervena LEDka
nalavo od vypinaca

1. SNAHA

(zapol som openbox + vlozeny USB s orig FW 2.10.67 so stlacenym CH-) vypis z programu PuTTY:

'1 Check first_boot = 30
set first_boot_env 1
(Re)start USB...
Front USB: scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
52311125 fac.optibox.anacondaplus.v2.10.67.ird
==> find ird fac.optibox.anacondaplus.v2.10.67.ird [52311125 ] <==

1 file(s), 0 dir(s)

reading uImage
ret=> -1
stopping USB..


NAND read: device 0 offset 0x500000, size 0x300000

Reading data from 0x7ff800 -- 100% complete.
3145728 bytes read: OK
init started: BusyBox v1.14.2 (2012-03-12 15:08:37 KST)
root::0:0:root:/root:/bin/sh
Starting app: #### ERROR Get System Information ##### (270431a0)
#### ERROR Get System Information ##### (270431a0)
#### ERROR Get System Information ##### (270431a0)
#### ERROR Get System Information ##### (270431a0)
#### ERROR Get System Information ##### (270431a0)
#### ERROR Get System Information ##### (270431a0)
///////////////////////////////
STFAE_Init......
///////////////////////////////
STFAE_Init 1
STFAE_Init 5
STFAE_Init 6
STFAE_Init 7
STFAE_Init 14
STFAE_Init 15
STFAE_Init 16
STFAE_Init 17
STFAE_Init 18
STFAE_Init 19
STFAE_Init 20
STFAE_Init 21
STFAE_Init 23
STFAE_Init 24
STFAE_Init 25
STFAE_Init 26
STFAE_Init 27
STFAE_Init 28
STFAE_Init 29
STFAE_Init 32
STFAE_Init 32
STFAE_Init 33
STFAE_Init 34
STFAE_Init 35
STFAE_Init 36
STFAE_Init 37
STFAE_Init 38

VOUT_FindI2cNumForHDMI 2

STFAE_Init 42
STFAE_Init OK
Front_IrInit : et6202_fd(ffffffff)
fd_front 29
# VFD type : 10001, ver : 1
_micom_type : 65537
..... [WiA8293_IicInit] error 0
..... pes start [0][0], buffer 0
..... pes start [0][0], signal 0
..... pes start [1][0], buffer 0
..... pes start [1][0], signal 0
..... pes start [0][1], buffer 0
..... pes start [0][1], signal 0
..... pes start [1][1], buffer 0
..... pes start [1][1], signal 0
============================================
====== Start Main Application =============
============================================
Init Wi OK
Appl> Thu Jun 30 22:00:57 UTC 2011



2. SNAHA

(zapol som openbox + vlozeny USB s orig FW 2.10.52 so stlacenym CH+) vypis z programu PuTTY:

'1 (Re)start USB...
Front USB: scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
49601818 fac.optibox.anacondaplus.v2.10.52.ird
==> find ird fac.optibox.anacondaplus.v2.10.52.ird [49601818 ] <==

1 file(s), 0 dir(s)

==> usb_loading start fac.optibox.anacondaplus.v2.10.52.ird
reading fac.optibox.anacondaplus.v2.10.52.ird
......................................................................................................................................
......................................................................................................................................
......................................................................................................................................
......................................................................................................................................
......................................................................................................................................
......................................................................................................................................
......................................................................................................................................
...................
ret=> 49601818
Loader_WriteFlashData[0] size=225500
Loader_WriteFlash size=0x370dc offset=0x0
Erasing at 0x20000 -- 100% complete.

Writing data at 0x0 -- 0% complete. [0 0]

Loader_WriteFlashData[1] size=52559872
Loader_WriteFlash size=0x3220002 offset=0x800000
Erasing at 0x67e0000 -- 100% complete.

Writing data at 0x800000 -- 0% complete. [0 0]
Writing data at 0x8c8000 -- 1% complete. [400 0]
Writing data at 0x92c000 -- 2% complete. [600 0]
Writing data at 0x990000 -- 3% complete. [800 0]
Writing data at 0xa58000 -- 4% complete. [1200 0]
Writing data at 0xabc000 -- 5% complete. [1400 0]
Writing data at 0xb20000 -- 6% complete. [1600 0]
Writing data at 0xb84000 -- 7% complete. [1800 0]
Writing data at 0xc4c000 -- 8% complete. [2200 0]
Writing data at 0xcb0000 -- 9% complete. [2400 0]
Writing data at 0xd14000 -- 10% complete. [2600 0]
Writing data at 0xddc000 -- 11% complete. [3000 0]
Writing data at 0xe40000 -- 12% complete. [3200 0]
Writing data at 0xea4000 -- 13% complete. [3400 0]
Writing data at 0xf08000 -- 14% complete. [3600 0]
Writing data at 0xfd0000 -- 15% complete. [4000 0]
Writing data at 0x1034000 -- 16% complete. [4200 0]
Writing data at 0x1098000 -- 17% complete. [4400 0]
Writing data at 0x1160000 -- 18% complete. [4800 0]
Writing data at 0x11c4000 -- 19% complete. [5000 0]
Writing data at 0x1228000 -- 20% complete. [5200 0]
Writing data at 0x128c000 -- 21% complete. [5400 0]
Writing data at 0x1354000 -- 22% complete. [5800 0]
Writing data at 0x13b8000 -- 23% complete. [6000 0]
Writing data at 0x141c000 -- 24% complete. [6200 0]
Writing data at 0x14e4000 -- 25% complete. [6600 0]
Writing data at 0x1548000 -- 26% complete. [6800 0]
Writing data at 0x15ac000 -- 27% complete. [7000 0]
Writing data at 0x1610000 -- 28% complete. [7200 0]
Writing data at 0x16d8000 -- 29% complete. [7600 0]
Writing data at 0x173c000 -- 30% complete. [7800 0]
Writing data at 0x17a0000 -- 31% complete. [8000 0]
Writing data at 0x1868000 -- 32% complete. [8400 0]
Writing data at 0x18cc000 -- 33% complete. [8600 0]
Writing data at 0x1930000 -- 34% complete. [8800 0]
Writing data at 0x1994000 -- 35% complete. [9000 0]
Writing data at 0x1a5c000 -- 36% complete. [9400 0]
Writing data at 0x1ac0000 -- 37% complete. [9600 0]
Writing data at 0x1b24000 -- 38% complete. [9800 0]
Writing data at 0x1bec000 -- 39% complete. [10200 0]
Writing data at 0x1c50000 -- 40% complete. [10400 0]
Writing data at 0x1cb4000 -- 41% complete. [10600 0]
Writing data at 0x1d18000 -- 42% complete. [10800 0]
Writing data at 0x1de0000 -- 43% complete. [11200 0]
Writing data at 0x1e44000 -- 44% complete. [11400 0]
Writing data at 0x1ea8000 -- 45% complete. [11600 0]
Writing data at 0x1f70000 -- 46% complete. [12000 0]
Writing data at 0x1fd4000 -- 47% complete. [12200 0]
Writing data at 0x2038000 -- 48% complete. [12400 0]
Writing data at 0x209c000 -- 49% complete. [12600 0]
Writing data at 0x2164000 -- 50% complete. [13000 0]
Writing data at 0x21c8000 -- 51% complete. [13200 0]
Writing data at 0x222c000 -- 52% complete. [13400 0]
Writing data at 0x22f4000 -- 53% complete. [13800 0]
Writing data at 0x2358000 -- 54% complete. [14000 0]
Writing data at 0x23bc000 -- 55% complete. [14200 0]
Writing data at 0x2420000 -- 56% complete. [14400 0]
Writing data at 0x24e8000 -- 57% complete. [14800 0]
Writing data at 0x254c000 -- 58% complete. [15000 0]
Writing data at 0x25b0000 -- 59% complete. [15200 0]
Writing data at 0x2614000 -- 60% complete. [15400 0]
Writing data at 0x26dc000 -- 61% complete. [15800 0]
Writing data at 0x2740000 -- 62% complete. [16000 0]
Writing data at 0x27a4000 -- 63% complete. [16200 0]
Writing data at 0x286c000 -- 64% complete. [16600 0]
Writing data at 0x28d0000 -- 65% complete. [16800 0]
Writing data at 0x2934000 -- 66% complete. [17000 0]
Writing data at 0x2998000 -- 67% complete. [17200 0]
Writing data at 0x2a60000 -- 68% complete. [17600 0]
Writing data at 0x2ac4000 -- 69% complete. [17800 0]
Writing data at 0x2b28000 -- 70% complete. [18000 0]
Writing data at 0x2bf0000 -- 71% complete. [18400 0]
Writing data at 0x2c54000 -- 72% complete. [18600 0]
Writing data at 0x2cb8000 -- 73% complete. [18800 0]
Writing data at 0x2d1c000 -- 74% complete. [19000 0]
Writing data at 0x2de4000 -- 75% complete. [19400 0]
Writing data at 0x2e48000 -- 76% complete. [19600 0]
Writing data at 0x2eac000 -- 77% complete. [19800 0]
Writing data at 0x2f74000 -- 78% complete. [20200 0]
Writing data at 0x2fd8000 -- 79% complete. [20400 0]
Writing data at 0x303c000 -- 80% complete. [20600 0]
Writing data at 0x30a0000 -- 81% complete. [20800 0]
Writing data at 0x3168000 -- 82% complete. [21200 0]
Writing data at 0x31cc000 -- 83% complete. [21400 0]
Writing data at 0x3230000 -- 84% complete. [21600 0]
Writing data at 0x32f8000 -- 85% complete. [22000 0]
Writing data at 0x335c000 -- 86% complete. [22200 0]
Writing data at 0x33c0000 -- 87% complete. [22400 0]
Writing data at 0x3424000 -- 88% complete. [22600 0]
Writing data at 0x34ec000 -- 89% complete. [23000 0]
Writing data at 0x3550000 -- 90% complete. [23200 0]
Writing data at 0x35b4000 -- 91% complete. [23400 0]
Writing data at 0x367c000 -- 92% complete. [23800 0]
Writing data at 0x36e0000 -- 93% complete. [24000 0]
Writing data at 0x3744000 -- 94% complete. [24200 0]
Writing data at 0x37a8000 -- 95% complete. [24400 0]
Writing data at 0x3870000 -- 96% complete. [24800 0]
Writing data at 0x38d4000 -- 97% complete. [25000 0]
Writing data at 0x3938000 -- 98% complete. [25200 0]
Writing data at 0x3a00000 -- 99% complete. [25600 0]

Loader_WriteFlashData[6] size=1916331
Loader_WriteFlash size=0x1d3dab offset=0x500000
Erasing at 0x7e0000 -- 100% complete.

Writing data at 0x500000 -- 0% complete. [0 0]
Writing data at 0x564000 -- 21% complete. [200 0]
Writing data at 0x5c8000 -- 42% complete. [400 0]
Writing data at 0x62c000 -- 64% complete. [600 0]
Writing data at 0x690000 -- 85% complete. [800 0]

___________________________________________________________
Po tomto to hned zastavi a BOX ukazuje COMPLETE.

- No tak pre mna to vyzera ze sa od*ajcila flash pamat ?

Prosiiim help me

PS: 1 Skusal som program HDbox Users data cleaner (cez rs 232)Ale ten len vypisuje hlasku:
Serial connected, sending stopbit 0 - 150, potom odznova.

PS: 2 Ked som skusal spustit s USB E2, nabehla uvodna obrazovka, potom bliklo 720p na telke potom bliklo znova a nic

PS: 3 Skusal som aj program porter. Ten zase ukazoval rozdielne cislo v % ako bolo na fyzickom BOXe
a niekde okolo 75% to vypisalo -19% v programe porter a na displayi sa zobrazilo
ERRvolaco.

Mam ho doma 4 DNI !!! Najhorsie je ze mi isiel FW 2.10.67 + USB enigma 2 popisana vyssie (stiahnuta z AB fora)

[revis]

hlavne nepanikar. Prerobil si prijimac na hdbox ? Preco sa tam cez USB snazis nahrat nespravnu verziu sw ?

[Peter_z_BB]

Neprerobil. Je to normalne kupeny optibox anaconda plus. Myslel som ze to nie je problem, ked su technicky zhodne. Nahral som optibox fw 2.10.68, potom som podla navodov tu na fore pre HD boxy nainstaloval enigmu 2 PKT a vsetko slapalo. Ked som vsak nahral opat fw 2.10.68, tak to zacalo blbnut.

[revis]

no - na optibox opat novsi sw uz asi nebude, ze ?
over,alebo znovu si stiahni tu verziu sw , ktora je urcena pre tvoj box.
to znamena, ze stare verzie z PC ,aj zozipovane zmaz.
Potom sa kukni na satdigitalne na postup pre upgrade cez konzolu.
pozor- sw musis dat na prazdy USB s FAT32 formatom .
http://www.forum.satdigitalne.cz/viewto ... 166&t=9826

[Peter_z_BB]

dakujem pekne, vyskusam, dam vediet.

[Peter_z_BB]

Bohuzial nepomohlo, narozdiel od spominaneho pripadu ( http://www.forum.satdigitalne.cz/viewto ... 166&t=9826) mne to zacalo "asi flashovat" firmware. Dal som 2.10.78


Loader_WriteFlashData[6] size=1916331
Loader_WriteFlash size=0x1d3dab offset=0x500000
Erasing at 0x7e0000 -- 100% complete.

Writing data at 0x500000 -- 0% complete. [0 0]
Writing data at 0x564000 -- 21% complete. [200 0]
Writing data at 0x5c8000 -- 42% complete. [400 0]
Writing data at 0x62c000 -- 64% complete. [600 0]
Writing data at 0x690000 -- 85% complete. [800 0]

tu my to skonci - na 85%

Ale su tam rôzne prikazy. Napriklad o odomknuti
(protect - enable or disable FLASH write protection)

a

(erase - erase FLASH memory)

ked som skusal erase all tak mi napisalo:

Erase Flash Bank # 1 Can't erase unknown flash type - aborted

[plesi]

Zkus toto:
http://technet.euweb.cz/2011/12/Postup- ... troju.html

[revis]

nejakym zazrakom sa ti dostali do flash data, ktore tam nepatria. stava sa to pri laborovani s nahravanim v enigma2 , ked uzivatel zvoli miesto na nahravanie flash..... dlho to nevydrzi .
chcelo by to odomknut oblast flash, kde su data a zmazat ju . to uz ale ty sam nezvladnes .
Inak - bootovanie sa da zastavit pocas startu klavesou medzernik na PC a potom sa da aj napisat help, kde je zoznam prikazov... Nedoporucujem ti to, zver prijimac nejakemu odbornikovi, ktory ti uvolni flash .

[Peter_z_BB]

to Plesi - dakujem pekne, ano to som skusal - program nedokaze vymazat pamat.
dakujem

to revis,
aha, takze treba odomknut pamat a to sa neda v domacich podmienkach (rs 232 kabel etc)?
Nemas nahodou skusenosti komu to zverit a kolko by to stalo ?

Takze to znamena ze ta flash pamat nie je znicena ? (Myslim tu cast kde to skonci na 85%)

Dakujem pekne za pomoc, ak by niekoho nieco napadlo kludne piste

S pozdravom Peter

[revis]

Peter_BB . Jasne,ze pamat nieje znicena. Pokazit flash sa neda. Treba sa poobzerat v okoli po odbornikovi. V okoli tvojho bydliska. A este lepsie je kontaktovat svojho predajcu, nech poradi .

[Peter_z_BB]

No tak sa to vyriesilo. Moj predajca odosle box na reklamaciu, kde pamat vymazu. Problem je udajne v tom ze nove anacondy plus, na rozdiel od starych nie pluskovych nepodporuju vymazavanie cez konzolu a cez prikaz erase all Robia to "nejakym" napajkovanim dosky.

Dakujem vsetkym, hlavne revisovi za pomoc.

PS: mozte to locknut alebo este mozem napisat ci sa im to podarilo vo fortise
zdarec

[efendy55]

no stou flesh by som si tak istý nebol .mne sa niečo podobné stalo na hdboxe 7100-ke . nič som neprehrával nič som nenastavoval až raz počas pozerania mi začal pyskovať ,,kodované " /ide ako klient v sieti v nebule v-1 tak som predpokladal že je v prdeli nebula / vytiahol som usb s enigmou strčil do zásuvky a tiež nič ani v org softe . prehral soft cez rs 232 a ani si neprdol . tak som ho poslal do servisu a v montážnom liste ja napísané ,, vadná flesh pamäť vymenená " prehrali mi tam novší soft tuším 2,67 poslali mi ho späť a od vtedy ked niečo strčím do usb tak len bootuje a bootuje / aj dva dni / a ani teplí prd , len je zaujímavé že ked tam strčím usb s nebulou tak nabehne perfektne a aj ide bez problémov ale v org softe ani bohovi ked niečo zacíti v usb -čku . asi ho budem znova reklamovať . a teraz mi poradte čo sa s tým dá spraviť ? že by bezbolestný rs 232 ?

[Peter_z_BB]

Takze problem je vyrieseny. Prijmac opat funguje. Vycistili pamat