ASUS WL 500 gp

[markan]

Nejsem si jisty, jestli bude hard reset spravne reseni pro muj staricky Asus WL500gx. S fw dd-wrt problem nemam, ten tam dostanu a plne funguje. Problem je s Tomato, na ktery se nemuzu pres web.prohlizec po upgradu dostat. Nasel sem nejaky postup, ze bych se mel pred upgrade na Tomato telnetem dostat na router s dd-wrt a prikazem tohle heslo upgradnout, ale netusim zatim jak.

[alfsvk]

Nemusel som robit nic zvlastne, skusal som to na default heslach
Inak pre DD WRT je web admin admin , ale telnet ide cez root admin
heslo zmenis v telnete prikazom

Kód: Vybrat vše

passwd

[joe6pack]

zgebol mi routrik s openwrt - ziadny reset nesiel, ani 30/30/30... ani telnet - total mrtvola...
po zapnuti ziadne bootovanie, iba okamzite trvale svietila ledka usb aj bez vlozeneho usb-cka...
skusil som strcit na usb backup a ejhle po zapnuti zacala saliet system ledka, tak to zostalo aj 1/2 hod; vtedy som skusil tl. reset - hura cez telnet isiel firstboot, nahodil som web a backup - routrik zije

[rosssss]

proverte si zdroje, zda je mate v poradku, on ten filtracni kondik umi pekne pozlobit

nebo si sezente movy zdroj, 3 nebo 3,5A stoji cca 250kc a mate po problemu (aspon u me)

[markan]

Tak odpoved na muj problemek by mela byt v tomhle http://www.polarcloud.com/tomatofaq#why ... sword_work. Jen to nejak nechapu......

[Kiker]

zgebol mi routrik s openwrt - ziadny reset nesiel, ani 30/30/30... ani telnet - total mrtvola...
po zapnuti ziadne bootovanie, iba okamzite trvale svietila ledka usb aj bez vlozeneho usb-cka...
skusil som strcit na usb backup a ejhle po zapnuti zacala saliet system ledka, tak to zostalo aj 1/2 hod; vtedy som skusil tl. reset - hura cez telnet isiel firstboot, nahodil som web a backup - routrik zije

ako ti pisal rosssss, skontroluj si zdroj.
Ak je zdroj OK, tak nez urobis reset, skontroluj si kondiky na doske ci nie su vydute. Mal som na taky na opravu a po vymene troch kondikov slape dalej.

[joe6pack]

v mojom pripade je hardver ok.
umrtvenie nastalo po "nestandardnom" laborovani.
dolezite je ze sa ho podarilo zobudit postupom, ktory som nikde nenasiel...

[korask]

tak omylom sa mi podarilo nahrat soft z tplink do asus 500gp v1 da sa stim este neco spravit jedine co sa da je ping na poslednu ip dik za radu

[rosssss]

mate nekdo na wl500gp v2 tomato nebo openwrt bez pouziti usb flash?

[ihilop]

Ako spravit automaticky restar routera, (napr. 1xdenne)?
Asusu 500gp fw. Oleg.

[davidas]

pokud mas vse spravne nastaveno, nepotrebujes nic restartovat

mam uptime i 90 dnu bez restartu



zde mas neco
http://www.ab-forum.info/viewtopic.php? ... &start=100

Tak mi nejede.Script mám podle návodu

Ja to mam vyriesene trosku inac, ale princip rovnaky:

v administration - commands mam len prikaz na spustenie skriptu:

Kód: Vybrat vše

/opt/./oscam.restart.sh

v /opt/ mam script "oscam.restart.sh" (dovod je ten, ze obcas sa mi stalo, ze prestal fungovat oscam, a nechcel som rebootovat router tak som jednoducho spustil tento skript - zapricinene to bolo USB hubom co som pouzival)

samotny "oscam.restart.sh" obsahuje nasledovne:

Kód: Vybrat vše

killall oscam
killall -9 oscam
START=90 
rmmod ftdi_sio 
rmmod usbserial 
insmod usbserial 
insmod ftdi_sio 
/opt/oscam/bin/./oscam -b -c /opt/oscam/bin &

v prilohe aj moj skript, atributy 755. Ak chces pouzit ine umiestnenie, nezabudni prepisat umiestnenie v "administration - commands"

K tvojmu problemu - mas vobec umiestnene usbserial.o a ftdi_sio v /jffs ???

[ihilop]

Som myslel restart celeho routera, nielen oscamu.

[mamanek]

Podle použitého softu..Openwrt-Kamikaze pod položkou crontabs třeba...sorry ,ted všiml toho Oleg.

[peter8205]

Konečne som rozbehal na asus rt n16 s fw RT-N16-1.9.2.7-rtn-r4667.trx oscam,
ale mam problem zdielanie mi ide len na jednom satelite a to na cryptoboxe 500 (CR500) a na cryptoboxe 200 sd(CR200SD) na lokalnej sieti uz to nejde satelit sa na loguje ok ale obraz nejde. V oscame ked dam userov. Tak tam vidim u prveho satelitu (CR500) connected OK 111 a cislo ktore udava nejake prenesene data. Ale u druheho satelitu CR200SD je connected OK NOK ziadne udaje Ale u polozky IGN su prenesene nejake pakety 111. Este ked dam asus do modu acces poit myslim ze je to teda vsetky aj WAN aj LAN porty funguju ako 5 LAN portov zdielanie prestane fungovat aj na tom jednom satelite. U newcs na asus wl 500 gp to tak fungovalo kde je problem ? Vopred dakujme za rady !!!

[Flavius]

zdravim
Mam nasledujici problem.
Postupoval jsem dle tohoto: http://ab-forum.info/viewtopic.php?f=18 ... start=1540
Mam Asus WL500gp v1 s firmwarem "OpenWRT Kamikaze 8.09" kernel 2.6.
Instalovany Oscam 4803. Oscam bezi v pohode, ale pokud vlozim Skylink ICE kartu nejede to.
Testnul jsem karty 0D0F, 0D03, 0D70 a vse v poradku, ale karta ICE nabehne s timto logem v horni i dolni ctecce. Nepodelil by se nekdo o funkcni binarku pro ICE a ostatni soubory ? diky
Zde je log:
--------------------------------------------------------------------------------------------
2012/12/22 22:01:44 400 s >> OSCam << cardserver started version 1.00-unstable_svn, build #4803 (mips-wrt54g-linux)
2012/12/22 22:01:44 400 s version=1.00-unstable_svn, build #4803, system=mips-wrt54g-linux, nice=-1
2012/12/22 22:01:44 400 s client max. idle=120 sec, debug level=0
2012/12/22 22:01:44 400 s max. logsize=30 Kb
2012/12/22 22:01:44 400 s client timeout=3000 ms, fallback timeout=2500 ms, cache delay=0 ms
2012/12/22 22:01:44 400 s auth size=4976
2012/12/22 22:01:44 400 s services reloaded: 0 services freed, 12 services loaded
2012/12/22 22:01:44 400 s userdb reloaded: 3 accounts loaded, 0 expired, 0 disabled
2012/12/22 22:01:44 400 s signal handling initialized (type=sysv)
2012/12/22 22:01:45 400 s 8929 service-id's loaded
2012/12/22 22:01:45 400 s can't open file "/jffs/oscam/bin/oscam.tiers" (err=2), no tier-id's loaded
2012/12/22 22:01:45 400 s can't open file "/jffs/oscam/bin/oscam.provid" (err=2), no provids's loaded
2012/12/22 22:01:45 400 s can't open file "/jffs/oscam/bin/oscam.ird" (errno=2) irdeto guessing not loaded
2012/12/22 22:01:45 400 s monitor: initialized (fd=10, port=10000)
2012/12/22 22:01:45 400 s camd33: disabled
2012/12/22 22:01:45 400 s camd35: disabled
2012/12/22 22:01:45 400 s cs378x: disabled
2012/12/22 22:01:45 400 s newcamd: initialized (fd=11, port=10010, crypted)
2012/12/22 22:01:45 400 s CAID: 0D0F
2012/12/22 22:01:45 400 s provid #0: 000004
2012/12/22 22:01:45 400 s provid #1: 000008
2012/12/22 22:01:45 400 s provid #2: 00000C
2012/12/22 22:01:45 400 s provid #3: 000010
2012/12/22 22:01:45 400 s newcamd: initialized (fd=12, port=10011, crypted)
2012/12/22 22:01:45 400 s CAID: 0D96
2012/12/22 22:01:45 400 s provid #0: 000004
2012/12/22 22:01:45 400 s provid #1: 000008
2012/12/22 22:01:45 400 s newcamd: initialized (fd=13, port=10012, crypted)
2012/12/22 22:01:45 400 s CAID: 0D02
2012/12/22 22:01:45 400 s provid #0: 00008C
2012/12/22 22:01:45 400 s provid #1: 0000A0
2012/12/22 22:01:45 400 s provid #2: 0000A4
2012/12/22 22:01:45 400 s provid #3: 0000A8
2012/12/22 22:01:45 400 s cccam: initialized (fd=14, port=12000, crypted)
2012/12/22 22:01:45 400 s radegast: disabled
2012/12/22 22:01:45 C04 h HTTP Server listening on port 8888
2012/12/22 22:01:45 400 s http thread started
2012/12/22 22:01:45 400 s creating thread for device /dev/ttyUSB0
2012/12/22 22:01:45 400 s creating thread for device /dev/ttyUSB1
2012/12/22 22:01:45 1406 r reader thread started (thread= 1406, label=int_0d96, device=/dev/ttyUSB1, detect=none, mhz=357, cardmhz=357)
2012/12/22 22:01:45 1005 r reader thread started (thread= 1005, label=int_0d0f, device=/dev/ttyUSB0, detect=none, mhz=357, cardmhz=357)
2012/12/22 22:01:45 400 s creating thread for device 192.168.1.99
2012/12/22 22:01:45 1807 p proxy thread started (thread= 1807, label=remote_0d02, server=192.168.1.99)
2012/12/22 22:01:45 1807 p connecting to 192.168.1.99
2012/12/22 22:01:45 400 s loadbalancer: can't read from file /tmp/.oscam/stat
2012/12/22 22:01:45 400 s waiting for local card init
2012/12/22 22:01:45 1807 p 192.168.1.99: resolved ip=192.168.1.99
2012/12/22 22:01:45 1807 p connect failed: timeout
2012/12/22 22:01:45 1807 p remote_0d02 network connect error!
2012/12/22 22:01:47 1406 r int_0d96 card detected
2012/12/22 22:01:47 1005 r int_0d0f card detected
2012/12/22 22:01:52 1005 r ATR: 00 00 00 00 00 00 00 00 00 00 00 00 00
2012/12/22 22:01:53 1005 r Maximum frequency for this card is formally 5 Mhz, clocking it to 3.57 Mhz
2012/12/22 22:01:54 1005 r [cryptoworks-reader] card detected
2012/12/22 22:01:54 1005 r [cryptoworks-reader] type: CryptoWorks
2012/12/22 22:01:54 1005 r type: CryptoWorks, caid: 0D96, ascii serial: 3xxxxxxxx, hex serial: xxxxxxxxxx
2012/12/22 22:01:54 1005 r issuer: CryptoWorks, id: 04, bios: v3, pin: unknown, mfid: 3F00
2012/12/22 22:01:54 1005 r providers: 4 (04,08,0C,10)
2012/12/22 22:01:54 1005 r found cardsystem cryptoworks
2012/12/22 22:01:55 1005 r provider: 1, id: 04, name: Operator: FFFF
2012/12/22 22:01:55 1005 r chid: 1772, date: 2012/11/02 - 2012/12/02, name: Product 1772
2012/12/22 22:01:55 1005 r chid: 03E9, date: 2012/11/02 - 2012/12/02, name: Product 03E9
2012/12/22 22:01:55 1005 r chid: 03EA, date: 2012/11/01 - 2012/12/01, name: Product 03EA
2012/12/22 22:01:55 1005 r chid: 03EB, date: 2012/11/02 - 2012/12/02, name: Product 03EB
2012/12/22 22:01:55 1005 r chid: 03EC, date: 2012/11/02 - 2012/12/02, name: Product 03EC
2012/12/22 22:01:55 1005 r chid: 03ED, date: 2012/11/02 - 2012/12/02, name: Product 03ED
2012/12/22 22:01:55 1005 r chid: 7FFD, date: 2012/11/02 - 2012/11/12, name: Product 7FFD
2012/12/22 22:01:55 1005 r chid: 7FFE, date: 2012/11/02 - 2012/12/02, name: Product 7FFE
2012/12/22 22:01:55 1005 r chid: FFD8, date: 2012/11/02 - 2012/12/02, name: Product FFD8
2012/12/22 22:01:55 1005 r chid: FFD0, date: 2012/11/02 - 2012/12/02, name: Product FFD0
2012/12/22 22:01:55 1005 r chid: 0000, date: 2000/01/00 - 2000/01/07, name: DownLo
2012/12/22 22:01:56 1005 r provider: 2, id: 08, name: Operator: FFFF
2012/12/22 22:01:56 1005 r chid: 0000, date: 2000/01/00 - 2000/01/07, name: DownLo
2012/12/22 22:01:56 1005 r provider: 3, id: 0C, name: Operator: FFFF
2012/12/22 22:01:56 1005 r chid: 0000, date: 2000/01/00 - 2000/01/07, name: DownLo
2012/12/22 22:01:56 1005 r provider: 4, id: 10, name: Operator: FFFF
2012/12/22 22:01:56 1005 r chid: 0000, date: 2000/01/00 - 2000/01/07, name: DownLo
2012/12/22 22:01:56 1005 r [cryptoworks-reader] ready for requests
2012/12/22 22:01:57 1406 r Error activating card.
2012/12/22 22:02:08 1406 r Error activating card.
2012/12/22 22:02:19 1406 r Error activating card.
2012/12/22 22:02:19 1406 r card initializing error
2012/12/22 22:02:20 400 s init for all local cards done
2012/12/22 22:02:20 400 s anti cascading disabled
---------------------------------------------------------------------------------------------

[Flavius]

Trosku jsem pokrocil i kdyz ne moc. Stale to nefunguje. Jde mi o pouziti ICE karty.
Vymenil jsem radu binarek oscamu az tusim po verzi 55xx. V tom to zrejme nebude.
Oscam jede spravne, kontroloval jsem pres putty a nacte i kartu a bez problemu se dostanu na web rozhrani oscamu, ale .....
Wincsc s protokolem newcamd 5.25 mi po prepnuti na kodovany program, kdy je videt ze blikla ctecka karet tedy, ze s nej. pravdepodobnosti cte data s karty, ukazuje nasledujici :
------------------------------------------------------------------
23-XII 18.42.22** Changing channel to: CT1
23-XII 18.42.22 Login OK to NCD Server [ asusWL500gp:10011 ]
23-XII 18.42.22 Searching next valid server (Reason: Keys Missing)
23-XII 18.42.22 [ Error(-1) NCD_Rx: Not Connected ]
23-XII 18.42.22 No more server available...
------------------------------------------------------------------

oscam log mi ukazuje nasledujici:
------------------------------------------------------------------
2012/12/23 18:42:22 1C07 c client connected to 10011 port
2012/12/23 18:42:22 1C07 c encrypted newcamd:10011-client 10.0.0.1 granted (user, au=auto (2 reader))
2012/12/23 18:42:22 1C07 c user user authenticated successfully (generic)
2012/12/23 18:42:22 1C07 c AU enabled for user user on reader int_0d96
2012/12/23 18:42:22 1C07 c Connection closed to client
2012/12/23 18:42:22 1C07 c user disconnected from 10.0.0.1
2012/12/23 18:42:22 1C07 c thread 1C07 ended!
------------------------------------------------------------------

Router provozuju pres "WAN port" a zacinam mit neblahy tuseni ze komunikace asi touhle
cestou nejak vazne ( .
V routeru adresar etc/config soubor firewall mam nasledujici
------------------------------------------------------------------
config 'defaults'
option 'syn_flood' '1'
option 'input' 'ACCEPT'
option 'output' 'ACCEPT'
option 'forward' 'REJECT'

config 'zone'
option 'name' 'lan'
option 'input' 'ACCEPT'
option 'output' 'ACCEPT'
option 'forward' 'REJECT'

config 'zone'
option 'name' 'wan'
option 'input' 'ACCEPT'
option 'output' 'ACCEPT'
option 'forward' 'REJECT'
option 'masq' '1'

config 'forwarding'
option 'src' 'lan'
option 'dest' 'wan'
option 'mtu_fix' ''

config 'forwarding'
option 'src' 'lan'
option 'dest' 'lan'
option 'mtu_fix' ''

config 'forwarding'
option 'src' 'wan'
option 'dest' 'lan'
option 'mtu_fix' ''
--------------------------------------------------------------------
Vedel by nekdo co jeste schazi ? nebo co tam ma byt a neni ?
diky komukoli

[peter8205]

toto su obrazky z mojho oscam serveru na asus rt n16
cryptobox 500hd sa mi pripoji ako user 1 , 2 alebo iný
ale cryptobox 200sd sa mi nepripoji ako user1 vid obrazok nevie niekto kde je
chyba ?
http://imgupload.sk/viewer.php?file=zxn ... 95xdhg.jpg
http://imgupload.sk/viewer.php?file=zkx ... w1i2sf.jpg

[peter8205]

cryptoboxu 200s ako user1 pribuda len hodnota cache 100 OK nič.
U cryptoboxu 500hd ako user2 pribuda honota OK a zdielanie ide.
Kde je problem preco sa cryptobox 200 s nevie pripojit a len cachuje ?

[peter8205]

poradi niekto s presmerovanim portov ?
Na momdeme mam smerovanie portov na IP 192.168.1.3 port 10011 na 10011
router rt n16 s oscam serverom
na konci start mam toto :
iptables -I INPUT -j ACCEPT -p tcp --dport 10011
router je v mode home gateway
ale ked dam tuto stranku :
http://www.yougetsignal.com/tools/open-ports/
port forward tester tak to stale pise port 10011 is close.
Nevie niekto kde je chyba ?

[peter8205]

ked zadam prikaz iptales -L vypise sa toto :

Kód: Vybrat vše

[admin@WL3 root]$ iptables -L
Chain INPUT (policy ACCEPT)
target     prot opt source               destination
ACCEPT     tcp  --  anywhere             anywhere            tcp dpt:10011
DROP       all  --  anywhere             anywhere            ctstate INVALID
ACCEPT     all  --  anywhere             anywhere            ctstate RELATED,ESTABLISHED
ACCEPT     all  --  anywhere             anywhere            ctstate NEW
ACCEPT     all  --  anywhere             anywhere            ctstate NEW