Raspberry + oscam

[VTronik]

A můžeš se přihlásit do oscamu na Raspberry přes webové rozhraní? Pokud ano, šel bych touto cestou, stačí jen vyplnit několik málo položek (ohledně čtečky, karty a userů) a nemusíš řešit kam a jak konfiguráky uložit. Oscam si je uloží sám tam kam potřebuje.

[lovuzdar]

Hoši nejde o biznis.... jsem pouze v domácí síti. Do teď jsem to měl na starém DM500....ale vyschly kondíky, začala vypadávat LAN a celkově už to nebylo OK, proto jsem přešel na PI3....
V konfigu se uživatelsky trochu vyznám.... Mám prostě problém s přechodem verze 1.00 na 1.20... Pokud bych měl funkční konfiguráky, ostatní už bych si nějak nastavil (snad).
Nejsem lenoch, už se s tím drb* docela dlouho a fakt nevím jak dál.....taks e nezlobte za můj (možná amatérský) dotaz.
lovuzdar!

[peter54]

Pouzi navod odtial - dal som tam vsetko, http://www.ab-forum.info/viewtopic.php?f=168&t=69750

konfigy z dm by mali fungovat akurat /dev/sci0 nahradis podla skutocnej citacky a zmienky o dvbapi vyhodis.
Ak by daco neislo, je tu konfigov hafo.
Ked pozorne precitas navod co som dal, najdes vzorove konfigy po kompilacii aj na svojej maline!

Kód: Vybrat vše

cd ../Distribution/doc/example/
   vi oscam.conf
      vi oscam.server
 Po kontrole tieto alebo ine vopred pripravene a konfiguráky nakopirujeme 
 do konfig adresára v tomto konkretnom prípade do 
      /etc/tuxbox/config/oscam ako je uvedené nizsie. 

Ked nebudem mat co na praci, mozem tam vecer prihodit svoje vzorove konfigy.
Pripadne napis co vlastne mas za konfiguraciu (citacky) a mozem ti to podat na zlatej tacke.

[peter54]

Toto rozbalit v /etc/tuxbox/config/oscam , na start oscamu pouzit skript z http://www.ab-forum.info/viewtopic.php?f=168&t=69750
a tu je ten poklad - cw, ice, pcsc, co hrdlo raci

Prajem bohate zazitky a keby nieco nefungovalo, reklamacie vybavuju na ministerstve zemetraseni.

[k.o.h.u.t.]

Návodů na internetu najdeš spousty, viz. kolega o příspěvěk výše. Nicméně pro většinu je to nic neříkající a jen opisování příkazů. Každého to stojí spousta času, které jsou k nezaplacení, a někdo si myslí, že mu to tu někdo celé napíše. Obecně platí, nejen pro OSCAM, čím míň "blbostí" do toho naplacáš, tím líp pro tebe.

Pokud mohu mluvit za sebe, a mám to odzkoušeno osobně (viz. příloha), tak: Raspbian, binárka kompilovánan (verze 10060). Nebudeš muset na nic šahat, když budeš potřebovat restartovat OSCAm, tak ho restartuješ, ale na Raspi nemusíš sáhnout jak je rok dlouhý. Měl jse ho skoro 2 roky v nepřetržitém provozu bez restartu, ale bohužel přišel výpadek elektřiny, tak jsem musel začít odznovu

[duri19]

Ahojte vie mi niekto poradit Na banana pi mam cez usb pripojeny tuto usb citacku:

Oscam som zbuildl poslednu verziu. USB citakcu mam v oscame.server device ako bus:device. Oscam mi kartu detekuje aj vidim zapisy (RTVS karta). Ked do boxu (dream,vu+) vlozim linku na pripojenie vidim aj v boxe ze mam jednu kartu ak vsak chcem sledovart stv1,2 tak mi stanicu neodkoduje a v oscam logu na banana mam chybu Invalid ecm type for card

[peter54]

To by si asi musel dat aj configy - inak len hadanie. Rtvs karta ide na 0668. Ked dlho lezala v sufliku, moze to trvat aj par hodin, nez sa zobudi.

[kratke_pole]

Preco par hodin ?
https://www.rtvs.org/a/150336_obnova-za ... karty-rtvs

[duri19]

To by si asi musel dat aj configy - inak len hadanie. Rtvs karta ide na 0668. Ked dlho lezala v sufliku, moze to trvat aj par hodin, nez sa zobudi.

Karta funguje v normalnom boxe, je to aktivna karta, chcel som ju presunut do tej smartgo citacky. Ked tam vlozim skyulink ice tak bezproblemov ide. Ked nastavim v boxe smartgo a device /dev/ttyUSB0 tak skylink karta ide ale rtvs nie pise ze nepodporovana karta

2018/09/13 17:06:09 7E9BCEC3 r (reader) rtvs [smargo] Buffers readed 0 bytes total time_us 75138
2018/09/13 17:06:09 7E9BCEC3 r (reader) rtvs [smargo] Reader initialized (device=/dev/ttyUSB0, detect=none, mhz= AUTO, cardmhz=534)
2018/09/13 17:06:10 7E9BCEC3 r (reader) rtvs [smargo] card detected
2018/09/13 17:06:17 7E9BCEC3 r (reader) rtvs [smargo] Error activating card.
2018/09/13 17:06:35 7E9BCEC3 r (-) -- Skipped 2 duplicated log lines --
2018/09/13 17:06:35 7E9BCEC3 r (reader) rtvs [smargo] THIS WAS A FAILED START ATTEMPT No 1 out of max alloted of 1
2018/09/13 17:06:35 7E9BCEC3 r (reader) rtvs [smargo] card initializing error
2018/09/13 17:07:36 08B1F780 h (reader) rtvs [smargo] Restarting reader
2018/09/13 17:07:36 08B1F780 h (reader) rtvs [smargo] creating thread for device /dev/ttyUSB0
2018/09/13 17:07:36 22BA808E r (reader) rtvs [smargo] Buffers readed 0 bytes total time_us 75149
2018/09/13 17:07:36 22BA808E r (reader) rtvs [smargo] Reader initialized (device=/dev/ttyUSB0, detect=none, mhz= AUTO, cardmhz=534)
2018/09/13 17:07:37 22BA808E r (reader) rtvs [smargo] card detected
2018/09/13 17:07:45 22BA808E r (reader) rtvs [smargo] ATR: 3B 0E 49 52 45 54 4F 20 43 20
2018/09/13 17:07:46 22BA808E r (reader) rtvs [smargo] card system not supported
2018/09/13 17:07:46 22BA808E r (reader) rtvs [smargo] Normal mode failed, reverting to Deprecated Mode
2018/09/13 17:07:54 22BA808E r (reader) rtvs [smargo] ATR: 3B 0E 49 52 45 54 4F 20 43 20
2018/09/13 17:07:55 22BA808E r (reader) rtvs [smargo] card system not supported
2018/09/13 17:07:55 22BA808E r (reader) rtvs [smargo] THIS WAS A FAILED START ATTEMPT No 1 out of max alloted of 1
2018/09/13 17:07:55 22BA808E r (reader) rtvs [smargo] card initializing error

[peter54]

To je jasné - presne tak vyzerá protokol, ked čítačka nedava 6mhz. Rtvs karta nepojde ani v citacke na obciansky, ani v tbs3102 nastavenej na 3,57 mhz.
Tvoja by sa mala dat preklopit na 6 mhz, ale to musí poradiť niekto, kto ju ma a komu sa to podarilo. Ice karta je ina, ta pojde aj na 3,57, cize vo vsetkom.
Skus tento postup https://wiki.vuplus-support.org/index.p ... martreader
A tu snad najdes nieco uzitocne http://www.sat-universe.com/showthread.php?t=257556
Uplne najjednoduchsie a je hodit tam tbs3102. Tam nahodis 6mhz prepínačom a chodi to spolahlivo.

[duri19]

2peter54 : Dakujem za radu pomocou smartcard tool sa mi podarilo nastavit 600MHz, kartu mi uz box vidi, nacita mi zapisy ale ked sa z ineho boxu na neho pripojim tak vypisuje : Invalid ecm type for card ak vlozim ice kartu nastavim reader pre ice kartu tak odkoduje. Oscam.server pre rtvs mam nastaveny nasledovne
[reader]
label = rtvs
protocol = smargo
device = /dev/ttyUSB0
caid = 0668
boxkey = B1B2B3B4B5B6B7B8
rsakey = AB722A8CAA9F58DE0D1CBB6FF329C961ED9DD759B103082D1BAE64C27A861D42E7F631891C2660EFA57484F80BBB4E0E8249A8368E31BD3FFC369FBE95160528
detect = none
mhz = 600
cardmhz = 600
group = 1
emmcache = 1,3,2,0

[peter54]

Nemam volnu citacku kde by som to vedel otestovat a rtvs mi momentalne bezi v boxe.
Tam dostane zapisy od dvbapi a potom sa zdiela uplne rovnako ako kazda ina karta. Domnievam sa, ze ti na rtvs kartu neprisli global zapisy.
Verim, ze si velmi blizko k uspechu . Potom daj vediet.

Skus si pre nu na banane spravit au uzivatela napriklad
Odskusane aspon medzi dvoma formulermi, ale formuler s kartou v standby, takze emm muselo prist z klienta.

[account]
user = rtvs_test
pwd = p
description = rtvs_test
au = rtvs
group = 1

a na klientovi spravit citacku s tym uzivatelom, ostatne citacky na klientovi po dobu testu radsej vypni

[reader]
label = rtvs_cli
protocol = cs378x
device = banana_ip,12005
user = rtvs_test
password = p
caid = 0668
group = 1
emmcache = 0,1,15,1

A este na klientovi pre usera dvbapi dopisat
[account]
user = dvbapiau
au = pi_sk,pi_cz,rtvs_cli
group = 1


vysledok:

Kód: Vybrat vše

2018/09/14 09:31:37 00000000 s     (main) Host name      = formuler4turbo
2018/09/14 09:31:37 00000000 s     (main) Release        = 4.8.3
2018/09/14 09:31:37 00000000 s     (main) Version        = #1 SMP Sat Oct 14 03:35:30 CEST 2017
2018/09/14 09:31:37 00000000 s     (main) Machine        = mips
2018/09/14 09:31:37 00000000 s     (main) Stb model      = dm800se
2018/09/14 09:31:37 00000000 s     (main) Stb boxtype    = formuler4turbo
2018/09/14 09:31:37 00000000 s     (main) creating pidfile /tmp/oscam.pid with pid 30220
2018/09/14 09:31:37 00000000 s   (config) services reloaded: 0 services freed, 4 services loaded, rejected 0
2018/09/14 09:31:37 00000000 s   (config) userdb reloaded: 2 accounts loaded, 0 expired, 0 disabled
2018/09/14 09:31:37 00000000 s     (main) signal handling initialized
2018/09/14 09:31:37 00000000 s   (config) 10 provid's loaded
2018/09/14 09:31:37 00000000 s   (config) 129 service-id's loaded in 1 ms
2018/09/14 09:31:37 00000000 s      (net) cs378x: initialized (fd=3, port=12005)
2018/09/14 09:31:37 00000000 s   (reader) pi_sk [cs378x] creating thread for device 192.168.0.91
2018/09/14 09:31:37 00000000 s   (reader) pi_cz [cs378x] creating thread for device 192.168.0.91
2018/09/14 09:31:37 00000000 s   (reader) rtvs [internal] creating thread for device /dev/sci0
2018/09/14 09:31:37 00000000 s     (stat) loadbalancer: could not open /tmp/.oscam/stat for reading (errno=2 No such file or directory)
2018/09/14 09:31:37 00000000 s     (main) waiting for local card init
2018/09/14 09:31:37 4C2B3AEE p   (reader) pi_sk [cs378x] proxy 192.168.0.91:12005
2018/09/14 09:31:37 4C2B3AEE p   (reader) pi_sk [cs378x] proxy initialized, server 192.168.0.91:12005
2018/09/14 09:31:37 13F00DF0 p   (reader) pi_cz [cs378x] proxy 192.168.0.91:12005
2018/09/14 09:31:37 13F00DF0 p   (reader) pi_cz [cs378x] proxy initialized, server 192.168.0.91:12005
2018/09/14 09:31:37 40A5F973 r   (reader) rtvs [internal] Reader initialized (device=/dev/sci0, detect=cd, mhz=600, cardmhz=600)
2018/09/14 09:31:37 40A5F973 r   (reader) rtvs [internal] Reader sci internal, detected box type: formuler4turbo
2018/09/14 09:31:37 375B7144 h    (webif) webif: decompressed 176767 bytes back into 435224 bytes
2018/09/14 09:31:37 375B7144 h    (webif) HTTP Server running. ip=:: port=8888
2018/09/14 09:31:38 40A5F973 r   (reader) rtvs [internal] card detected
2018/09/14 09:31:54 40A5F973 r   (reader) rtvs [internal] ERROR: no characters found in ATR!
2018/09/14 09:31:54 40A5F973 r   (reader) rtvs [internal] Deactivating card
2018/09/14 09:31:54 40A5F973 r   (reader) rtvs [internal] Read ATR fail, attempt 1/5  fs = 3
2018/09/14 09:31:55 40A5F973 r   (reader) rtvs [internal] ATR: 3B 9F 21 0E 49 52 44 45 54 4F 20 41 43 53 20 56 37 2E 30 9F 
2018/09/14 09:31:55 40A5F973 r   (reader) rtvs [internal] Init card protocol T14, FI=2, F=558, D=1, N=0
2018/09/14 09:31:55 40A5F973 r   (reader) rtvs [internal] Calculated work ETU is 93.00 us reader mhz = 600
2018/09/14 09:32:00 40A5F973 r   (reader) rtvs [internal] Buffers readed  0 bytes total time_us 5505295
2018/09/14 09:32:01 40A5F973 r   (reader) rtvs [internal] ATR Fsmax is 6 MHz, clocking card to 6.00 (specified in reader->mhz)
2018/09/14 09:32:02 40A5F973 r   (reader) rtvs [internal] detect irdeto card
2018/09/14 09:32:02 40A5F973 r   (reader) rtvs [internal] Irdeto SC 70 version 2 revision 0, patch level 2
2018/09/14 09:32:02 40A5F973 r   (reader) rtvs [internal] caid: 0668, acs: 0.06, country code: SVK
2018/09/14 09:32:02 40A5F973 r   (reader) rtvs [internal] providers: 4, ascii serial: ##########, hex serial: ######, hex base: ##
2018/09/14 09:32:05 40A5F973 r   (reader) rtvs [internal] active providers: 4 (03f7c9,ffffff,ffffff,ffffff)
2018/09/14 09:32:05 40A5F973 r   (reader) rtvs [internal] found card system irdeto
2018/09/14 09:32:05 40A5F973 r   (reader) rtvs [irdeto] THIS WAS A SUCCESSFUL START ATTEMPT No  1 out of max alloted of 1
2018/09/14 09:32:05 40A5F973 r   (reader) rtvs [irdeto] entitlements for provider: 1, id: 03F7C9
2018/09/14 09:32:05 40A5F973 r   (reader) rtvs [irdeto] chid: 0006, date: 2018/09/14 - 2019/05/26
2018/09/14 09:32:06 40A5F973 r   (reader) rtvs [irdeto] chid: 7FFE, date: 2018/03/23 - 2018/04/22
2018/09/14 09:32:10 40A5F973 r   (reader) rtvs [irdeto] ready for requests
2018/09/14 09:32:11 00000000 s     (main) init for all local cards done
2018/09/14 09:32:11 00000000 s (emmcache) loaded 0 emmcache records from /tmp/.oscam/oscam.emmcache in 0 ms
2018/09/14 09:32:11 00000000 s (emmcache) loaded 0 emmstat records from /tmp/.oscam/oscam.emmstat in 0 ms
2018/09/14 09:32:11 00000000 s (anticasc) anti cascading disabled
2018/09/14 09:32:11 0927B1DF c   (client) plain dvbapi-client granted (dvbapiau, au=auto (4 reader))
2018/09/14 09:32:11 1C0C1BF2 c   (client) encrypted cs378x-client 192.168.0.114 granted (rtvs_test, au=on (1 reader))
2018/09/14 09:32:11 0927B1DF c   (dvbapi) dvbapi channelcache loaded from /etc/tuxbox/config/oscam/oscam.ccache
2018/09/14 09:32:11 0927B1DF c   (dvbapi) Detected /dev/dvb/adapter0/demux0 Api: 0, userconfig boxtype: 1 maximum amount of possible filters is 32 (oscam limit is 32)
2018/09/14 09:32:11 0927B1DF c   (dvbapi) PMT6: Trying connect to enigma CA PMT listen socket...
2018/09/14 09:32:11 0927B1DF c   (dvbapi) PMT6 CA PMT Server connected on fd 11!
2018/09/14 09:32:11 1C0C1BF2 c   (camd35) rtvs_test emm-request sent (reader=rtvs, caid=0668, auprovid=03F7C9)
2018/09/14 09:32:11 1C0C1BF2 c      (ecm) rtvs_test (0668@000000/0000/1329/4F:F57D2E2ADBE8686C3A0181E824A84AE2): rejected  (122 ms) by rtvs (Invalid ecm type for cardst)
2018/09/14 09:32:11 40A5F973 r   (reader) rtvs [irdeto] rtvs_test emmtype=shared, len=60 (hex: 0x3C), cnt=0: error (104 ms)
2018/09/14 09:32:11 40A5F973 r   (reader) rtvs [irdeto] rtvs_test emmtype=global, len=37 (hex: 0x25), cnt=0: written (79 ms)
2018/09/14 09:32:11 40A5F973 r   (reader) rtvs [irdeto] rtvs_test emmtype=shared, len=60 (hex: 0x3C), cnt=0: skipped (103 ms)
2018/09/14 09:32:11 40A5F973 r   (reader) rtvs [irdeto] rtvs_test emmtype=global, len=37 (hex: 0x25), cnt=0: written (78 ms)
2018/09/14 09:32:12 40A5F973 r   (reader) rtvs [irdeto] rtvs_test emmtype=global, len=64 (hex: 0x40), cnt=0: written (110 ms)
2018/09/14 09:32:12 40A5F973 r   (reader) rtvs [irdeto] rtvs_test emmtype=shared, len=62 (hex: 0x3E), cnt=0: written (105 ms)
2018/09/14 09:32:12 40A5F973 r   (reader) rtvs [irdeto] rtvs_test emmtype=global, len=37 (hex: 0x25), cnt=0: written (79 ms)
2018/09/14 09:32:12 1C0C1BF2 c      (ecm) rtvs_test (0668@000000/0000/1329/4F:D6BD987D92A3D8B89D343A0101B04640): found (923 ms) by rtvs
2018/09/14 09:32:12 40A5F973 r   (reader) rtvs [irdeto] rtvs_test emmtype=shared, len=60 (hex: 0x3C), cnt=0: written (103 ms)
2018/09/14 09:32:12 40A5F973 r   (reader) rtvs [irdeto] rtvs_test emmtype=global, len=37 (hex: 0x25), cnt=0: written (79 ms)
2018/09/14 09:32:12 40A5F973 r        (-) -- Skipped 1 duplicated log lines --
2018/09/14 09:32:12 40A5F973 r   (reader) rtvs [irdeto] rtvs_test emmtype=shared, len=60 (hex: 0x3C), cnt=0: skipped (103 ms)
2018/09/14 09:32:12 40A5F973 r   (reader) rtvs [irdeto] rtvs_test emmtype=global, len=37 (hex: 0x25), cnt=0: written (78 ms)
2018/09/14 09:32:13 1C0C1BF2 c      (ecm) rtvs_test (0668@000000/0000/1329/4F:5102AB208C5CFA120EE1891BAFEEF4C6): found (1508 ms) by rtvs

[duri19]

2peter54: dakujem za radu, uz to ide tak ako ma.

[duri19]

Este jedna otazka mam doma este usb citacku gemalto gempc twin rozbehal somj ju v banane (debian) cez pcsc aj v oscame, ale cita mi len skylink ice aj v irdeto mode, ak vsak vlozim rtvs kartu tak neznama karta, vie niekto poradit , reader pre rtvs som dal takyto:
[reader]
label = rtvs
enable = 0
protocol = pscs
device = 0
services = rtvs
autospeed = 0
caid = 0668
boxkey = B1B2B3B4B5B6B7B8
rsakey = AB722A8CAA9F58DE0D1CBB6FF329C961ED9DD759B103082D1BAE64C27A861D42E7F631891C2660EFA57484F80BBB4E0E8249A8368E31BD3FFC369FBE95160528
detect = cd
group = 4

[marci70]

A preco mas enable=0 ? A aj device

[peter54]

To nepojde. 6mhz z gemalta nedostanes.
Ostatne ako protocol=pcsc a enable = 0 povazujem za preklepy.
Ak by sa ti to nahodou nejak podarilo, rad sa priucim.

[peter54]

Pre kompletnost tu som dal vzorove konfigy pre oscam

[duri19]

To nepojde. 6mhz z gemalta nedostanes.
Ostatne ako protocol=pcsc a enable = 0 povazujem za preklepy.
Ak by sa ti to nahodou nejak podarilo, rad sa priucim.

gemalto som nevedel dat cez iny protokol ako pcsc : http://www.streamboard.tv/wiki/OSCam/en ... CSC_Reader ale to enable je preklep

[duri19]

A preco mas enable=0 ? A aj device

enable je preklep a device=0 je preto lebo je to protocol pcsc a ked usb citacka cez pcsc pri scane pcsc_scan je ako 0, ak ich mas viacej tak potom dalsia je 1,2,3....

pcsc_scan
PC/SC device scanner
V 1.4.27 (c) 2001-2011, Ludovic Rousseau <ludovic.rousseau@free.fr>
Compiled with PC/SC lite version: 1.8.17
Using reader plug'n play mechanism
Scanning present readers...
0: Gemalto PC Twin Reader 00 00

Tue Sep 18 22:02:53 2018
Reader 0: Gemalto PC Twin Reader 00 00
Card state: Card removed,

[peter54]

To nepojde. 6mhz z gemalta nedostanes.
Ostatne ako protocol=pcsc a enable = 0 povazujem za preklepy.
Ak by sa ti to nahodou nejak podarilo, rad sa priucim.

gemalto som nevedel dat cez iny protokol ako pcsc : http://www.streamboard.tv/wiki/OSCam/en ... CSC_Reader ale to enable je preklep

Este raz: ty tam mas pscs miesto pcsc.
Osobne som sa dosť natrapil s rtvs v gemalto a problem je, ze pcsc lite nepodporuje nastavenie frekvencie a rtvs musi mat 6mhz. Ice karty v tom idu bez problemov ci uz ako irdeto alebo cw.
Tak pouzivam gemalto na pki login do firemnej siete a k zakaznikom ale keby sa v tom niekomu podarilo rozbehať, rad sa necham poučiť.