SmartReader V2 / Phoenix / Smargo + oscam

[smyky]

Ahoj,
Prosim o radu.
Mam externi ctecku SmertReader V2 a prijimac vu+ zero
Interni ctecku jsem rozchodil, ale nevim jak definovat USB v (reader) device tak aby si oscam sahl pres usb na externi ctecku.

Hledal jsem tu a nasel par tipu.
device:
001:001
002:002
/dev/ttyUSB0

atd, ale ani jedno nefunguje.

Dekuju za tipy.

[sharkys]

http://www.streamboard.tv/wiki/OSCam/en ... treader.2B

...já mám Serial:Reader BDXXXXX .... myslím, že jsem to tehdy zjišťoval přes nějakou utilitu.

Jo a musíš mít OSCAM s podporou USB.

[marecek29]

A taky smargo.

[martin.domes]

Mám toto nastavení, ale nejede mi to :
Nevíte co mám blbě?

Kód: Vybrat vše

[reader]
label                         = IRDETO
enable                        = 0
protocol                      = mouse
device                        = /dev/ttyUSB0
detect                        = cd
mhz                           = 600
caid                          = 0624
cardmhz                       = 369
boxkey                        = B1B2B3B4B5B6B7B8
rsakey                        = AB722A8CAA9F58DE0D1CBB6FF329C961ED9DD759B103082D1BAE64C27A861D42E7F631891C2660EFA57484F80BBB4E0E8249A8368E31BD3FFC369FBE95160528
force_irdeto                  = 1
group                         = 1
emmcache                      = 1,1,2,0
saveemm-unknown               = 1
saveemm-u                     = 1
saveemm-s                     = 1
saveemm-g                     = 1

[vlasto]

log ti nepovedal nic?

[marci70]

enable 0 ani nemoze ist, ked to je vypnute si myslim

[martin.domes]

enable mám samozřejmně na 1, potom co mi to nešlo jsem to vypl., log teď nemám , zítra až to budu zkoušet tak ho sem vložím.

[merlyno]

Ahoj, podívej se do Dev jestli náhodou to usb není ttyUSB1, nebo jine číslo já nastavoval taky tuto čtečku a problém jsem měl právě tady, že jsem ju zapojil do druhého USB a tak jsem místo 0 měl 1 a mudroval jsem. Tak uvidíš.

[Spencer]

Asi by bolo vhodne napísať akú čítačku používaš, ako máš nastavene jumpre, ... .
Možno niekto používa rovnakú a bude vedieť poradiť.

[martin.domes]

mám phoenix/smartmouse card reader, jumpry na 5v, phoenix a 6 mhz

[matov]

Vidi ju oscam? Readers-scan USB

[martin.domes]

já bych řekl že vidí, log:
2021/01/24 18:13:09 120718D0 r (reader) IRDETO [irdeto] Warning: needed try nr 2, next ECM has some delay
2021/01/24 18:13:10 7B4D5B14 c (ecm) bin1 (0624@000000/0000/3391/5F:E567157220412D65EC8E3F7E69E88405): timeout (5000 ms) by IRDETO
2021/01/24 18:13:14 7B4D5B14 c (ecm) bin1 (0624@000000/0000/3391/5F:6E8A9F8070677C04BF77D1BA62116267): timeout (5000 ms) by IRDETO
2021/01/24 18:13:19 120718D0 r (reader) IRDETO [irdeto] Maybe you have a bad Cam Key set it from config file
2021/01/24 18:13:20 7B4D5B14 c (ecm) bin1 (0624@000000/0000/3391/5F:6E8A9F8070677C04BF77D1BA62116267): timeout (5000 ms) by IRDETO
2021/01/24 18:13:24 7B4D5B14 c (ecm) bin1 (0624@000000/0000/3391/5F:6E2AF32282FD1993CAECCD9D666FC070): timeout (5000 ms) by IRDETO
2021/01/24 18:13:29 120718D0 r (reader) IRDETO [irdeto] Warning: needed try nr 2, next ECM has some delay
2021/01/24 18:13:30 7B4D5B14 c (ecm) bin1 (0624@000000/0000/3391/5F:6E2AF32282FD1993CAECCD9D666FC070): timeout (5000 ms) by IRDETO
2021/01/24 18:13:34 7B4D5B14 c (ecm) bin1 (0624@000000/0000/3391/5F:64CC29E88ADF851209C4EEDEC45C883E): timeout (5001 ms) by IRDETO

[martin.domes]

toto je při startu oscamu log:

2021/01/24 14:33:56 43C228F4 h (webif) HTTP Server running. ip=0.0.0.0 port=10001
2021/01/24 14:33:56 120718D0 r (reader) IRDETO [mouse] Reader initialized (device=/dev/ttyUSB0, detect=cd, mhz=600, cardmhz=369)
2021/01/24 14:33:58 00000000 s (main) init for all local cards done
2021/01/24 14:33:58 00000000 >> OSCam << cardserver log switched, version 1.20_svn, build r11678 (x86_64-linux-gnu)
2021/01/24 18:00:12 120718D0 r (reader) IRDETO [mouse] card detected
2021/01/24 18:00:14 120718D0 r (reader) IRDETO [mouse] ATR: 3B 78 12 00 00 54 C4 03 00 8F F1 90 00
2021/01/24 18:00:14 120718D0 r (reader) IRDETO [mouse] Setting baudrate to 32258 bps
2021/01/24 18:00:15 120718D0 r (reader) IRDETO [mouse] Hist. Bytes: TĦ#3;
2021/01/24 18:00:15 120718D0 r (reader) IRDETO [mouse] detect irdeto card
2021/01/24 18:00:15 120718D0 r (reader) IRDETO [mouse] caid: 0624, acs: 0.06, country code: CZE
2021/01/24 18:00:15 120718D0 r (reader) IRDETO [mouse] providers: 4, ascii serial: ##########, hex serial: ######, hex base: ##
2021/01/24 18:00:15 120718D0 r (reader) IRDETO [mouse] WARNING: For Irdeto cards you will have to set 'cardmhz= 600' in oscam.server
2021/01/24 18:00:15 120718D0 r (reader) IRDETO [mouse] active providers: 4 (711aff,ffffff,ffffff,ffffff)
2021/01/24 18:00:15 120718D0 r (reader) IRDETO [mouse] found card system irdeto
2021/01/24 18:00:15 120718D0 r (reader) IRDETO [irdeto] THIS WAS A SUCCESSFUL START ATTEMPT No 1 out of max allotted of 1
2021/01/24 18:00:15 120718D0 r (reader) IRDETO [irdeto] entitlements for provider: 1, id: 711AFF
2021/01/24 18:00:15 120718D0 r (reader) IRDETO [irdeto] chid: 138E, date: 2012/07/29 - 2012/08/17
2021/01/24 18:00:15 120718D0 r (reader) IRDETO [irdeto] chid: 138F, date: 2012/07/29 - 2012/08/17
2021/01/24 18:00:15 120718D0 r (reader) IRDETO [irdeto] chid: 7FFC, date: 2021/01/24 - 2021/02/23
2021/01/24 18:00:15 120718D0 r (reader) IRDETO [irdeto] chid: 03E9, date: 2021/01/23 - 2021/02/23
2021/01/24 18:00:15 120718D0 r (reader) IRDETO [irdeto] chid: 03EA, date: 2021/01/23 - 2021/02/23
2021/01/24 18:00:15 120718D0 r (reader) IRDETO [irdeto] chid: 03EC, date: 2021/01/23 - 2021/02/23
2021/01/24 18:00:15 120718D0 r (reader) IRDETO [irdeto] chid: 03ED, date: 2021/01/23 - 2021/02/23
2021/01/24 18:00:15 120718D0 r (reader) IRDETO [irdeto] chid: 7FFE, date: 2021/01/24 - 2021/02/23
2021/01/24 18:00:15 120718D0 r (reader) IRDETO [irdeto] chid: FFB0, date: 2021/01/23 - 2021/02/23
2021/01/24 18:00:15 120718D0 r (reader) IRDETO [irdeto] chid: 7FFD, date: 2021/01/24 - 2021/02/03
2021/01/24 18:00:15 120718D0 r (reader) IRDETO [irdeto] chid: FFE0, date: 2021/01/23 - 2021/02/23
2021/01/24 18:00:15 120718D0 r (reader) IRDETO [irdeto] chid: FFD8, date: 2021/01/24 - 2021/02/03
2021/01/24 18:00:15 120718D0 r (reader) IRDETO [irdeto] chid: 03EB, date: 2021/01/23 - 2021/02/23
2021/01/24 18:00:15 120718D0 r (reader) IRDETO [irdeto] chid: 1771, date: 2021/01/23 - 2021/02/23
2021/01/24 18:00:16 120718D0 r (reader) IRDETO [irdeto] ready for requests

[matov]

Ano. Vidi ju.
(reader) IRDETO [irdeto] Maybe you have a bad Cam Key set it from config file

[martin.domes]

dal jsem tam tyto klíče
boxkey = A1C6F3D8B5E1F2C1
rsakey = 79EA25A763DA2C3E02B456A13962E60BCE63E628A2C177BE951CED96A9C6131A146F98D5867B7AE6682324FD6481913C0241F065C8D3457E54BB59B7B5DE0362

a log je tento:

2021/01/24 18:30:17 72003AE7 c (ecm) bin1 (0624@000000/0000/3391/5F:3F27B027D1D4C796A3F618A5E68726E2): not found (61 ms) by IRDETO
2021/01/24 18:30:21 5C7DF87F r (reader) IRDETO [irdeto] Maybe you don't have the entitlements for this channel
2021/01/24 18:30:21 72003AE7 c (ecm) bin1 (0624@000000/0000/3391/5F:FA1A654E55E1A5C952F8645BC8226AB1): not found (65 ms) by IRDETO
2021/01/24 18:30:27 5C7DF87F r (reader) IRDETO [irdeto] Maybe you don't have the entitlements for this channel
2021/01/24 18:30:27 72003AE7 c (ecm) bin1 (0624@000000/0000/3391/5F:FA1A654E55E1A5C952F8645BC8226AB1): not found (62 ms) by IRDETO

[matov]

Zapisy EMM mas active?

[EnoSat]

hlavne si v logu pozri ci ti chodia EMM , bez toho sa ti karta nerozbehne

[martin.domes]

jak mám nasatavit ty EMM zápisy aby chodily?

[VTronik]

Nastav to takto:

Kód: Vybrat vše

[reader]
label                         = IRDETO
enable                        = 1
protocol                      = mouse
device                        = /dev/ttyUSB0
detect                        = cd
mhz                           = 600
caid                          = 0624
cardmhz                       = 369
boxkey                        = A1C6F3D8B5E1F2C1
rsakey                        = 79EA25A763DA2C3E02B456A13962E60BCE63E628A2C177BE951CED96A9C6131A146F98D5867B7AE6682324FD6481913C0241F065C8D3457E54BB59B7B5DE0362
needsemmfirst                 = 1
ident                         = 0624:000000
force_irdeto                  = 1
group                         = 1
emmcache                      = 1,1,2,0

[EnoSat]

jak mám nasatavit ty EMM zápisy aby chodily?

v boxe povolit v DVB-Api AU , pripadne v Users povolit klientovi AU