oscam (klient) v 9105+ nahodne prestava dekodovat

[sbf]

Po prepnuti programu sa niekedy spamata, niekedy nie a treba natvrdo vypnut, niekedy sa ani potom nespamata a po case naskoci z nicoho nic....
Poradite niekto co to moze sposobovat...? Vsade v configoch mam len caid 0D96, odkial cita tie doleuvedene caid? (tj 0666, 0d03 atd)?

2013/05/02 19:27:35 1838 2A0C14E8 c dummy (0666&000000/1F44/0124/0000/46:C4DD/00-00): rejected caid (0 ms) (invalid caid 666)
2013/05/02 19:27:38 1838 2A0C14E8 c dummy (0D96&000004/1F44/0F02/0000/80:A3F9/00-00): timeout (15182 ms) by newcamd_skylink (try 2)
2013/05/02 19:27:38 1838 2A0C14E8 c dummy (0D0F&000004/1F44/0654/0000/7C:0124/00-00): rejected caid (0 ms) (invalid caid d0f)
2013/05/02 19:27:38 1838 2A0C14E8 c dummy (0D03&000004/1F44/0610/0000/9C:842C/00-00): rejected caid (1 ms) (invalid caid d03)
2013/05/02 19:27:38 1838 2A0C14E8 c dummy (0D70&000004/1F44/0702/0000/71:AC66/00-00): rejected caid (0 ms) (invalid caid d70)
2013/05/02 19:27:39 1838 2A0C14E8 c dummy (0624&000000/1F44/0F03/0000/50:BBFC/00-00): rejected caid (1 ms) (invalid caid 624)
2013/05/02 19:27:39 1838 2A0C14E8 c stapi: try pids again #3
2013/05/02 19:27:39 1838 2A0C14E8 c stapi: can't decode channel

[sbf]

oscam.conf
[global]
logfile = stdout
disablelog = 1
clienttimeout = 15000
unlockparental = 1
nice = -1
maxlogsize = 50
waitforcards = 0

[monitor]
port = 0
nocrypt =
aulow = 30
hideclient_to = 15
monlevel = 2
appendchaninfo = 0

[newcamd]
port = 30000@0D96:000004
key = 0102030405060708091011121314
allowed =
keepalive = 1
mgclient = 1

[dvbapi]
enabled = 1
au = 1
boxtype = none
user = dummy
pmt_mode = 0
request_mode = 0

oscam.dvbapi
S: PTI pmt1_1.tmp
S: PTI pmt1_2.tmp
S: PTI pmt1_3.tmp
S: PTI pmt1_4.tmp
S: PTI1 pmt2_1.tmp
S: PTI1 pmt2_2.tmp
S: PTI1 pmt2_3.tmp
S: PTI1 pmt2_4.tmp
S: PTI2 pmt3_1.tmp
P:0D96

oscam.user
[account]
user = dummy
pwd = ****
group = 1
hostname = (adresa)
au = 1
services = skylink_ice
caid = 0D96
ident = 0D96:000004

oscam.server
[reader]
label = newcamd_skylink
enable = 1
protocol = newcamd
device = adresa,port
key = 0102030405060708091011121314
user = dummy
password = heslo
services = skylink_ice
fallback = 1
caid = 0D96
group = 1

oscam.services
[skylink_ice]
caid = 0D96
provid = 000004
srvid = vsetky mozne.....

[Pastoman]

dopln si do oscam.dvbapi takto:


P: 0D96 1
I: 0D03
I: 0D70
I: 0624
I: 0666
I: 0D0F

[davidas]

ver, ze ani tohle nepomuze......

diky temto jevum jsem tam vratil orig fw kde se tento problem neprojevuje

[sbf]

ale toto sa prave v origo fw prejavuje... (e2 som neskusal)
ale pomohlo to trochu, teraz slape tak 3 hodky, potom prestane citat data (v logu pise nieco ako cannot receive 14 bytes of data alebo nieco v tom zmysle...) hoci siet a server je v poriadku, aj siet. karta na 9105 funguje...

[davidas]

tento problem se mi vyskytoval pouze v kombinaci s E2

s orig fw, bez problemu jede jak pila

[Noro C]

Zmeň binarku oscamu za inú, niektoré oscami blbnú. Treba testovať.

[davidas]

zvlastni, vzdyt to ani neumela binarka v E2 uz vlozena.....
ja jsem to vyresil, zpet k orig fw....
az bude dalsi vydani E2, zkusim, pokud to nepojede, opet zpet k orig fw

toz tak

ps-binarky jsem zkousel x-krat, je hdbox sh4? je, pouzil jsem binarku i nastaveni z ip boxu55hd kde jela bez problemu, stejne nastaveni konfigu, stejne a neresitelne priznaky padu

treba tomu nerozumim tak jak ty, nebo ostatni, ale vratil jsem tam orig fw, kde to slape ok, nic vic nepotrebuju....